Allied 96G1DFE Скачать руководство пользователя

Страница: 45 / 53

507769-04

Page 45 of 53

Issue 1927

Cleaning Heat Exchanger

If cleaning the heat exchanger becomes necessary,

follow the below procedures and refer to Figure 1 when

disassembling unit. Use papers or protective covering in

front of furnace while removing heat exchanger assembly.

1. Turn off electrical and gas supplies to the furnace.

2.  Remove the furnace access panels.
3.  Disconnect the 2 wires from the gas valve.
4.  Remove  gas  supply  line  connected  to  gas  valve.

Remove gas valve/manifold assembly.

5. Remove sensor wire from sensor. Disconnect 2 pin

plug from the ignitor.

6. Disconnect wires from flame rollout switches.
7. Loosen clamps at vent elbow. Disconnect condensate

drain tubing from flue collar and remove the vent

elbow.

8. Remove four burner box screws at the vestibule panel

and remove burner box. Set burner box assembly

aside.

NOTE:

If necessary, clean burners at this time. Follow

procedures outlined in Burner Cleaning section.

9. Mark and disconnect all combustion air pressure

tubing from cold end header collector box.

10. Mark and remove wires from pressure switches.

Remove pressure switches. Keep tubing attached to

pressure switches.

11. Disconnect the plug from the combustion air inducer.

Remove two screws which secure combustion air

inducer to collector box. Remove combustion air

inducer assembly. Remove ground wire from vest

panel.

12. Remove electrical junction box from the side of the

furnace.

13. Mark and disconnect any remaining wiring to heating

compartment components. Disengage strain relief

bushing and pull wiring and bushing through the hole

in the blower deck.

14. Remove the primary limit from the vestibule panel.
15. Remove two screws from the front cabinet flange at

the blower deck. Spread cabinet sides slightly to allow

clearance for removal of heat exchanger.

16.

Remove screws along vestibule sides and bottom

which secure vestibule panel and heat exchanger

assembly to cabinet. Remove two screws from blower

rail which secure bottom heat exchanger flange.

Remove heat exchanger from furnace cabinet.

17. Back wash heat exchanger with soapy water solution

or steam. If steam is used it must be below 275°F

(135°C).

18. Thoroughly rinse and drain the heat exchanger. Soap

solutions can be corrosive. Take care to rinse entire

assembly.

19. Reinstall heat exchanger into cabinet making sure

that the clamshells of the heat exchanger assembly

are resting on the support located at the rear of the

cabinet. Remove the indoor blower to view this area

through the blower opening.

20. Resecure the supporting screws along the vestibule

sides and bottom to the cabinet. Reinstall blower and

mounting screws.

21. Reinstall cabinet screws on front flange at blower

deck.

22. Reinstall the primary limit on the vestibule panel.
23. Route heating component wiring through hole in

blower deck and reinsert strain relief bushing.

24. Reinstall electrical junction box.
25. Reinstall the combustion air inducer. Reconnect the

combustion air inducer to the wire harness.

26. Reinstall pressure switches and reconnect pressure

switch wiring.

27. Carefully connect combustion air pressure switch

hosing from pressure switches to proper stubs on cold

end header collector box.

28.  Reinstall condensate trap.
29.  Reconnect exhaust piping and exhaust drain tubing.
30.  Reinstall burner box assembly in vestibule area.
31.  Reconnect flame rollout switch wires.
32.

Reconnect sensor wire and reconnect 2 pin plug from

ignitor.

33. Secure burner box assembly to vestibule panel using

four existing screws. Make sure burners line up in

center of burner ports.

34. Reinstall gas valve manifold assembly. Reconnect gas

supply line to gas valve.

35. Reconnect 2 wires to gas valve.
36. Replace the blower compartment access panel.
37.

Refer to instruction on verifying gas and electrical

connections when re-establishing supplies.

38. Follow lighting instructions to light and operate furnace

for 5 minutes to ensure that heat exchanger is clean

and dry and that furnace is operating properly.

39. Replace heating compartment access panel.

Cleaning the Burner Assembly

1. Turn off electrical and gas power supplies to furnace.

Remove upper and lower furnace access panels.

2.  Disconnect the 2 pin plug from the gas valve.
3.  Remove the burner box cover.
4.  Disconnect  the  gas  supply  line  from  the  gas  valve.

Remove gas valve/manifold assembly.

5. Mark and disconnect sensor wire from the sensor.

Disconnect 2 pin plug from the ignitor at the burner

box.

Содержание 96G1DFE






















































Результаты поиска

Содержание 96G1DFE

Отзывы:

Похожие инструкции для 96G1DFE

Бренды по названию

Популярные бренды

Allied 96G1DFE, Руководство по установке

Результаты поиска

Содержание 96G1DFE

Отзывы:

Похожие инструкции для 96G1DFE

Бренды по названию

Популярные бренды