Allied 96G1DFE Скачать руководство пользователя

Страница: 19 / 53

507769-04

Page 19 of 53

Issue 1927

Figure 25.

Equipment in Confined Space

(Inlet Air from Ventilated Attic and Outlet Air to

Outside)

If this unit is being installed in an application with

combustion air coming in from a space serviced by an

exhaust fan, power exhaust fan, or other device which

may create a negative pressure in the space, take care

when sizing the inlet air opening. The inlet air opening

must be sized to accommodate the maximum volume

of exhaust air as well as the maximum volume of

combustion air required for all gas appliances serviced

by this space.

CAUTION

Figure 26.

Equipment in Confined Space

(Inlet Air from Ventilated Crawl Space and Outlet Air

to Outside)

General Guidelines for Vent Terminations

In Non-Direct Vent applications, combustion air is taken

from indoors and the flue gases are discharged to the

outdoors. This unit is then classified as a non-direct vent,

Category IV gas furnace.

In Direct Vent applications, combustion air is taken from

outdoors and the flue gases are discharged to the outdoors.

This unit is then classified as a direct vent, Category IV gas

furnace.

In both Non-Direct Vent and Direct Vent applications, the

vent termination is limited by local building codes. In the

absence of local codes, refer to the current National Fuel

Gas Code ANSI Z223-1/NFPA 54 in U.S.A., and current

CSA-B149 Natural Gas and Propane Installation Codes in

Canada for details.

Position termination according to location given in Figure

27 or Figure 28. In addition, position termination so it is

free from any obstructions and 12” above the average

snow accumulation.

At vent termination, care must be taken to maintain

protective coatings over building materials (prolonged

exposure to exhaust condensate can destroy protective

coatings). It is recommended that the exhaust outlet not be

located within 6 feet (1.8 m) of a condensing unit because

the condensate can damage the painted coating.

NOTE:

If winter design temperature is below 32° F (0° C), it

is recommended that the exhaust piping be insulated with

1/2” (13 mm), Armaflex or equivalent when run through an

unconditioned area. In extremely cold climate areas with

temperature below 20° F (6.7° C) it is recommended that

3/4” (19 mm) Armaflex or equivalent be used. Insulation on

outside runs of exhaust pipe may be painted or wrapped

to protect insulation from deterioration in accordance with

the insulation manufacturers recommendation. Exhaust

pipe insulation may not be necessary in some specific

applications.

NOTE:

During extremely cold temperatures, below

approximately 20° F (6° C), units with long runs of vent

pipe through unconditioned space, even when insulated,

may form ice in the exhaust termination that prevents the

unit from operating properly. Longer run times of at least 5

minutes will alleviate most icing problems. Also, a heating

cable may be installed on exhaust piping and termination

to prevent freeze-ups. Heating cable installation kits are

available, see unit specification sheets for part numbers.

Do not use screens or perforated metal in exhaust

terminations. Doing so will cause freeze-ups and may

block the terminations.

IMPORTANT

Содержание 96G1DFE






















































Результаты поиска

Содержание 96G1DFE

Отзывы:

Похожие инструкции для 96G1DFE

Бренды по названию

Популярные бренды

Allied 96G1DFE, Руководство по установке

Результаты поиска

Содержание 96G1DFE

Отзывы:

Похожие инструкции для 96G1DFE

Бренды по названию

Популярные бренды