Allied 96G1DFE Скачать руководство пользователя страница 35

Страница: 35 / 53

507769-04

Page 35 of 53

Issue 1927

Figure 56. Typical Field Wiring Diagram

NOTE-

IF ANY WIRE IN THIS APPLIANCE IS REPLACED,

IT MUST BE REPLACED WITH WIRE OF LIKE

SIZE, RATING, INSULATION THICKNESS AND

TERMINATION.

WARNING-

ELECTRIC SHOCK HAZARD. CAN CAUSE

INJURY OR DEATH. UNIT MUST BE GROUNDED

IN ACCORDANCE WITH NATIONAL AND LOCAL

CODES.

‘R’ IS REQUIRED ON SOME OUTDOOR UNITS

L13 POWER CHOKE USED ON 3/4 AND 1 HP

ONLY

S145 IS USED WITH HONEYWELL GAS VALVE

WHEN APPLIED IN LP GAS UNTIS

mode when the combustion air inducer is operating and

the pressure switch is closed. Any humidifier rated up to

0.5 amp can be connected to this terminal with the ground

leg of the circuit connected to ground or the “C” terminal.

Figure 55. Furnace & Condensing Unit Thermostat

Designations

Thermostat

Furnace

Condensing

Unit

(Refer to specific thermostat and outdoor unit.)

COMMON

POWER

HEAT

INDOOR BLOWER

COOLING

CONDENSING

*CONDENSING

Install the room thermostat according to the instructions

provided with the thermostat. See Figure 55 for thermostat

designations. If the furnace is being matched with a

heat pump, refer to the FM21 installation instruction or

appropriate dual fuel thermostat instructions.

Indoor Blower Speeds

1. When the thermostat is set to “FAN ON”, the indoor

blower will run continuously on the fan speed when

there is no cooling or heating demand. See Table 17

for allowable continuous circulation speeds.

2. When the furnace is running in the heating mode, the

indoor blower will run on the heating speed.

3. When there is a cooling demand, the indoor blower will

run on the cooling speed.

Generator Use - Voltage Requirements

The following requirements must be kept in mind when

specifying a generator for use with this equipment:

•

The furnace requires 120 volts ± 10% (Range: 108

volts to 132 volts).

•

The furnace operates at 60 Hz ± 5% (Range: 57 Hz

to 63 Hz).

•

The furnace integrated control requires both polarity

and proper ground. Both polarity and proper grounding

should be checked before attempting to operate the

furnace on either permanent or temporary power.

•

Generator should have a wave form distortion of less

than 5% THD (Total Harmonic Distortion).

Содержание 96G1DFE






















































Результаты поиска

Содержание 96G1DFE

Отзывы:

Allied 96G1DFE, Руководство по установке, Страница: 35 / 53

Результаты поиска

Содержание 96G1DFE

Отзывы: