Allied 92G1UH Скачать руководство пользователя страница 25

Страница: 25 / 57

506724-01

Page 25 of 57

Issue 1108

FIGURE 29

VENT TERMINATION CLEARANCES

FOR DIRECT VENT INSTALLATIONS IN THE USA AND CANADA

INSIDE CORNER

DETAIL

VENT TERMINAL

AIR SUPPLY INLET

AREA WHERE TERMINAL
IS NOT PERMITTED

Fixed

Closed

Operable

Fixed

Closed

Operable

A =

B =

C =

D =

E =

F =

G =

H =

I =

J =

K =

L =

M =

US Installations

Canadian Installations

12 inches (305mm) or 12 in. 305mm)

above average snow accumulation.

12 inches (305mm) or 12 in. 305mm)

above average snow accumulation.

Clearance above grade, veranda,

porch, deck or balcony

Clearance to window or

door that may be opened

6 inches (152mm) for appliances <10,000

Btuh (3kw), 9 inches (mm) for appliances

> 10,000 Btuh (3kw) and <50,000 Btuh

(15 kw), 12 inches (305mm) for ap-

pliances > 50,000 Btuh (15kw)

6 inches (152mm) for appliances <10,000

Btuh (3kw), 12 inches (305mm) for

appliances > 10,000 Btuh (3kw) and

<100,000 Btuh (30kw), 36 inches (.9m)

for appliances > 100,000 Btuh (30kw)

Clearance to permanently

closed window

Vertical clearance to ventilated soffit

located above the terminal within a

horizontal distance of 2 feet (mm)

from the center line of the terminal

Clearance to unventilated soffit

Clearance to outside corner

Clearance to inside corner

Clearance to each side of center line ex-

tended above meter / regulator assembly

Clearance to service regulator

vent outlet

Clearance to non−mechanical air

supply inlet to building or the com-

bustion air inlet to any other ap-

pliance

Clearance to mechanical air sup-

ply inlet

Clearance above paved sidewalk or

paved driveway located on public property

Clearance under veranda, porch,

deck or balcony

* 12"

* 7 feet (2.1m)

3 feet (.9m) within a height 15 feet (4.5m)

above the meter / regulator assembly

3 feet (.9m)

6 inches (152mm) for appliances <10,000

Btuh (3kw), 9 inches (mm) for appliances

> 10,000 Btuh (3kw) and <50,000 Btuh

(15 kw), 12 inches (305mm) for ap-

pliances > 50,000 Btuh (15kw)

6 inches (152mm) for appliances <10,000

Btuh (3kw), 12 inches (305mm) for

appliances > 10,000 Btuh (3kw) and

<100,000 Btuh (30kw), 36 inches (.9m)

for appliances > 100,000 Btuh (30kw)

3 feet (.9m) above if within 10 feet

(3m) horizontally

6 feet (1.8m)

In accordance with the current ANSI Z223.1/NFPA 54 Natural Fuel Gas Code

In accordance with the current CSA B149.1, Natura

l Gas and Prop ane Installation Code

*For clearances not specified in ANSI Z223.1/NFPA 54 or CSA

B149.1, clear-

ance will be in accordance with local installation c

odes and the requirements

of the gas supplier and these installation instructions."

between two single family dwellings and serves both dwellings.

sides beneath the floor. Lennox recommends avoiding this location if possible.

* 12"

* Equal to or greater than soffit depth

* No minimum to outside corner

3 feet (.9m) within a height 15 feet (4.5m)

above the meter / regulator assembly

3 feet (.9m)

Содержание 92G1UH


























































Результаты поиска

Содержание 92G1UH

Отзывы:

Похожие инструкции для 92G1UH

Бренды по названию

Популярные бренды

Allied 92G1UH, Руководство по установке

Результаты поиска

Содержание 92G1UH

Отзывы:

Похожие инструкции для 92G1UH

Бренды по названию

Популярные бренды