manualshive.com logo in svg

Allied Telesis AT-GS950/10PS, Руководство по установке, Страница: 66 / 72

Поделиться
Скачать
Allied Telesis AT-GS950/10PS Скачать руководство пользователя страница 66

Chapter 3: Troubleshooting

66

Problem 3:

 A twisted pair port on the switch is connected to a network 

device, but the port’s LINK/ACT LED is off.

Solutions:

 The port is unable to establish a link to a network device. Try 

the following:

Verify that the network device connected to the twisted pair port is 
powered on and is operating properly.

Verify that the twisted pair cable is securely connected to the port 
on the media converter channel and to the port on the remote 
network device.

Verify that the port is connected to the correct twisted pair cable. 
This is to eliminate the possibility that the port is connected to the 
wrong network device, such as a powered-off device.

Try connecting another network device to the twisted pair port with 
a different cable. If the twisted pair port is able to establish a link, 
then the problem is with the cable or the other network device.

Verify that the twisted pair cable does not exceed 100 meters (328 
feet).

Verify that you are using the appropriate category of twisted pair 
cable: Category 3 or better for 10 Mbps operation and Category 5 
and Category 5E for 100 and 1000 Mbps operation.

Note

A 1000Base connection may require 5 to 10 seconds to establish a 
link.

Problem 4:

 The LINK/ACT LED for an SFP transceiver is off.

Solutions:

 The fiber optic port on the transceiver is unable to establish a 

link to a network device. Try the following:

Verify that the network device connected to the fiber optic port is 
operating properly.

Verify that the fiber optic cable is securely connected to the port on 
the media converter channel and to the port on the remote network 
device.

Check that the SFP module is fully inserted in the slot.

Verify that the operating specifications of the fiber optic ports on 
the SFP transceiver and the remote network device are 
compatible.

Verify that the correct type of fiber optic cabling is being used.

Verify that the port is connected to the correct fiber optic cable. 
This is to eliminate the possibility that the port is connected to the 
wrong remote network device, such as a powered off device.

Содержание AT-GS950/10PS









































































Отзывы:

Нет отзывов