Alliance Laundry Systems YDEE5BGS173CW01 Скачать руководство пользователя страница 31

Страница: 31 / 48

D515518ENR2

To reduce the risk of electric shock, fire, explosion, serious injury or death:

• Disconnect electric power to the dryer(s) before servicing.

• Close gas shut-off valve to gas dryer(s) before servicing.

• Never start the dryer(s) with any guards/panels removed.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the dryer is properly grounded.

W001R1

WARNING

Section 4

Error Codes

Display

Description

Cause/Corrective Action

Ero

Locked rotor error: The motor is not sensed as

rotating when it should be.

Terminate cycle and check that nothing is obstructing

motor rotation. Check wire harness connection

between motor, user control and output board, or try

replacing the user control or the output board. Clear

error with a key press.

Eop

Open thermistor error: The thermistor circuit

is sensed as being physically open.

Remove any lint build up around thermistor. Check

wire harness connection between thermistor and

harness. If problem persists replace thermistor, harness

or output board. Thermistor must no longer be seen as

open to clear.

Esh

Shorted thermistor error: The thermistor

circuit is sensed as being shorted.

Remove any lint build up around thermistor. Check

wire harness connection between thermistor and

harness. If problem persists replace thermistor, harness

or output board. Thermistor must no longer be seen as

shorted to clear.

Ens

Motor output shorted error: Hardware error.

Terminate cycle. Replace output board. Power down

machine to clear.

E59

Door input acquisition error: Hardware error. Terminate cycle. Replace output board. Power down

machine to clear.

E60

Centrifugal switch input acquisition error:

Hardware error.

Terminate cycle. Replace output board. Power down

machine to clear.

E61

High limit thermostat input acquisition error:

Hardware error.

Advance cycle to cool down. Replace output board.

Power down machine to clear.

Eco

Output board communication error:

Communication failure.

Power down machine to clear, power up and try again.

If error persists, check harness connection between

user control and output board, or try replacing the user

control or the output board.

Enr

Output board not ready error: Hardware

failure.

Terminate cycle. Replace output board. Power down

machine to clear.

(continued)

Содержание YDEE5BGS173CW01

















































Результаты поиска

Содержание YDEE5BGS173CW01

Отзывы:

Похожие инструкции для YDEE5BGS173CW01

Бренды по названию

Популярные бренды

Alliance Laundry Systems YDEE5BGS173CW01, Руководство по устранению неисправностей

Результаты поиска

Содержание YDEE5BGS173CW01

Отзывы:

Похожие инструкции для YDEE5BGS173CW01

Бренды по названию

Популярные бренды