Allen-Bradley MicroLogix 1762-IF2OF2 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

background image

MicroLogix™ Analog Input/Output Module

7

Publication 1762-IN005A-US-P

System Assembly

The expansion I/O module is attached to the controller or another I/O module by

means of a ribbon cable

after

mounting as shown below.

NOTE

Use the pull loop on the connector to disconnect modules. Do

not pull on the ribbon cable.

!

WARNING

EXPLOSION HAZARD

• In Class I, Division 2 applications, the bus connector must

be fully seated and the bus connector cover must be

snapped in place.

• In Class I, Division 2 applications, all modules must be

mounted in direct contact with each other as shown on
page 6. If DIN rail mounting is used, an end stop must be
installed ahead of the controller and after the last 1762 I/O

module.

Allen-Bradley HMIs

«
...
5
6
7
8
9
...
»

Содержание MicroLogix 1762-IF2OF2

























Отзывы:

Нет отзывов

Похожие инструкции для MicroLogix 1762-IF2OF2

PROFINET BNI PNT-508-055-P067

Бренд: Balluff Страницы: 84

Бренд: DayTronic Страницы: 414

Бренд: Harman Страницы: 10

Бренд: VENCO Страницы: 44

Бренд: Wabtec Страницы: 106

Stick Up Cam Wired

Бренд: ring Страницы: 9

RainStation RS-0001

Бренд: EarthMinded Страницы: 16

Бренд: Watts Страницы: 73

Бренд: RAPIBREW Страницы: 67

RAV6351 ILPVS1340

Бренд: rav Страницы: 152

Бренд: Euroscreen Страницы: 39

Бренд: Farfisa Страницы: 48

Бренд: M-system Страницы: 10

SwitchPoint Infinity 3

Бренд: Stryker Страницы: 124

Бренд: Jensen Audio Страницы: 20

Бренд: HOLOVISION Страницы: 4

Бренд: Zepro Страницы: 92

NC-MP-4A4B-12DLA/AL1403

Бренд: Norgren Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды