Allen-Bradley MicroLogix 1762-IF2OF2 Скачать руководство пользователя страница 18

Страница: 18 / 24

MicroLogix™ Analog Input/Output Module

Publication 1762-IN005A-US-P

Specifications

General Specifications

Specification

Value

Dimensions

90 mm (height) x 87 mm (depth) x 40 mm (width)
height including mounting tabs is 110 mm

3.54 in. (height) x 3.43 in. (depth) x 1.58 in. (width)
height including mounting tabs is 4.33 in.

Approximate Shipping Weight
(with carton)

240g (0.53 lbs.)

Storage Temperature

-40°C to +85°C (-40°F to +185°F)

Operating Temperature

0°C to +55°C (-32°F to +131°F)

Operating Humidity

5% to 95% non-condensing

Operating Altitude

2000 meters (6561 feet)

Vibration

Operating: 10 to 500 Hz, 5G, 0.030 in. max. peak-to-peak

Shock

Operating: 30G

Bus Current Draw (max.)

40 mA at 5V dc

105 mA at 24V dc

Analog Normal Operating Range

Voltage: 0 to 10V dc

Current: 4 to 20 mA

Full Scale

(1)

Analog Ranges

Voltage: 0 to 10.5V dc

Current: 0 to 21 mA

Resolution

12 bits (unipolar)

Repeatability

(2)

±0.1%

Input and Output Group to System
Isolation

30V ac/30V dc rated working voltage

(3)

(N.E.C. Class 2 required)
(IEC Class 2 reinforced insulation)

type test: 500V ac or 707V dc for 1 minute

Module Power LED

On: indicates power is applied.

Recommended Cable

Belden™ 8761 (shielded)

Содержание MicroLogix 1762-IF2OF2

























Результаты поиска

Содержание MicroLogix 1762-IF2OF2

Отзывы:

Похожие инструкции для MicroLogix 1762-IF2OF2

Бренды по названию

Популярные бренды

Allen-Bradley MicroLogix 1762-IF2OF2, Руководство по установке

Результаты поиска

Содержание MicroLogix 1762-IF2OF2

Отзывы:

Похожие инструкции для MicroLogix 1762-IF2OF2

Бренды по названию

Популярные бренды