Allen-Bradley MicroLogix 1762-IF2OF2 Скачать руководство пользователя страница 22

Страница: 22 / 24

MicroLogix™ Analog Input/Output Module

Publication 1762-IN005A-US-P

Hazardous Location Considerations

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or

non-hazardous locations only. The following WARNING statement applies to
use in hazardous locations.

WARNING

EXPLOSION HAZARD

• Substitution of components may impair suitability for

Class I, Division 2.

• Do not replace components or disconnect equipment unless

power has been switched off.

• Do not connect or disconnect components unless power has

been switched off.

• This product must be installed in an enclosure.

• In Class I, Division 2 applications, the bus connector must

be fully seated and the bus connector cover must be
snapped in place.

• In Class I, Division 2 applications, all modules must be

mounted in direct contact with each other as shown on

page 6. If DIN rail mounting is used, an end stop must be
installed ahead of the controller and after the last 1762 I/O
module.

• All wiring must comply with N.E.C. article 501-4(b).

Содержание MicroLogix 1762-IF2OF2

























Результаты поиска

Содержание MicroLogix 1762-IF2OF2

Отзывы:

Похожие инструкции для MicroLogix 1762-IF2OF2

Бренды по названию

Популярные бренды

Allen-Bradley MicroLogix 1762-IF2OF2, Руководство по установке

Результаты поиска

Содержание MicroLogix 1762-IF2OF2

Отзывы:

Похожие инструкции для MicroLogix 1762-IF2OF2

Бренды по названию

Популярные бренды