background image

Publication 1762-IN005A-US-P

Installation Instructions

MicroLogix™ Analog Input/Output 
Module

(Catalog Number 1762-IF2OF2)

Inside…

For More Information................................................................................2

Description ................................................................................................3

Installation ................................................................................................4

Mounting...................................................................................................5

System Assembly......................................................................................7

Field Wiring Connections..........................................................................8

Input Type Selection ................................................................................ 8

Output Type Selection ............................................................................. 8

Wiring ..................................................................................................... 9

I/O Memory Mapping .............................................................................13

Specifications .........................................................................................18

Hazardous Location Considerations .......................................................22

Environnements dangereux ....................................................................23

Allen-Bradley HMIs

Содержание MicroLogix 1762-IF2OF2

























Отзывы: