manualshive.com logo in svg

Allen-Bradley InView Marquee 2706-P42, Руководство пользователя

Поделиться
Скачать
Allen-Bradley InView Marquee 2706-P42 Скачать руководство пользователя страница 200

Publication 2706-UM016A-EN-P - June 2002

10-12

        InView Control InView Control API

•

Description

 - This method is used to trigger a message to stop 

running on the display. The remove message command will be 
sent to the display address set by the 

DisplayAddress

 property. 

DisplayAddress

 should be set before calling this method.

SingleMessage

•

Syntax -

HRESULT 

SingleMessage

(short nMessageNumber)

•

Parameters

 - 

nMessageNumber

The number of the sole message to be added to
the queue of running messages.

•

Return Value -

S_OK - Success

E_FAIL - Failure

•

Description -

This method is used to trigger a single message to 

run on the display. Any messages currently running on the 
display will be removed. The message to trigger must be 
downloaded to the display before it can be triggered. The single 
message command will be sent to the display address set by the 

DisplayAddress

 property. 

DisplayAddress

 should be set 

before calling this method.

UpdateVariable

•

Syntax -

HRESULT 

UpdateVariable

(short nVariable, long nValue)

•

Parameters -

nVariable

The variable number to update. 
Valid values are 0 - 99.

nValue

The new value for the variable. The display is
limited to 16-bit numbers, which can be signed or
unsigned.

•

Return Value -

S_OK - Success

E_FAIL - Failure

•

Description -

This method is used to update a variable in the 

display. If the variable is embedded in a running message, the 
new value will be shown. The update variable command will be 
sent to the display address set by the 

DisplayAddress

 property. 

DisplayAddress

 should be set before calling this method.

Содержание InView Marquee 2706-P42





















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды