Allen-Bradley InView Marquee 2706-P42 Скачать руководство пользователя страница 13

Страница: 13 / 212

Publication 2706-UM016A-EN-P - June 2002

InView Marquee Message Display Installation

1-7

Wall Mounting

Remove the 4 screws and the end cap from one end of the sign.

Slide one of the wall mounting brackets onto the back of the
sign until it is approximately 0.5 in. away from the end of the
sign.

Use two 10-32 x 1/4 Phillips screws (supplied) to secure the wall
mounting bracket to the back of the sign. Torque the screws to
2.7 Nm (24 lb-in).

Replace the end cap using the 4 screws removed in Step 1
above. Torque the screws to 2.7 Nm (24 lb-in).

Repeat Steps 1 to 4 for the other end of the sign. Distances
between the bracket holes, center-to-center, should be
approximately:

Attach the two remaining wall mounting brackets to a wall so
that they align with the brackets on the sign.

TIP

Remove only one end cap at a time.

Remove
these
screws.

Wall mounting
bracket

0.5”

Wall
mounting
bracket

Phillips
screws go
here.

Fasten
these
screws.

37 in (94 cm) for 2706-P42 and
72.2 in (183 cm) for 2706-P43
73 in (185.4 cm) for 2706-P44.

Allen-Bradley Spares

Содержание InView Marquee 2706-P42





















































































































































































































Результаты поиска

Содержание InView Marquee 2706-P42

Отзывы:

Бренды по названию

Популярные бренды

Allen-Bradley InView Marquee 2706-P42, Руководство пользователя

Результаты поиска

Содержание InView Marquee 2706-P42

Отзывы:

Бренды по названию

Популярные бренды