manualshive.com logo in svg

Allen-Bradley InView Marquee 2706-P42, Руководство пользователя

Поделиться
Скачать
Allen-Bradley InView Marquee 2706-P42 Скачать руководство пользователя страница 137

1

Publication 2706-UM016A-EN-P - June 2002

Chapter

 9

InView Protocol

Introduction

The purpose of this document is to show the protocol that is required 
to trigger messages and update variables on Allen-Bradley InView 
display with the InView Protocol.

In general, messages are downloaded through the software and stored 
within the display’s memory. Up to 4000 messages and 100 variables 
can be created with the InView software.

Messages can be displayed using the Control-T function, Modbus 
ASCII. One of three different methods can be used; 1) Priority 
Messaging, 2) Add a Message, 3) Remove a Displayed Message. 
Variables can be updated using the Control-V function or Modbus 
ASCII.

Triggering Messages and 
Updating Variables

The two functions that can be used to trigger messages and update 
variables are the Control-T (CRTL-T) and the Control-V (CTRL-V). The 
CTRL-T function allows for two different ways of displaying messages: 
Priority Messaging and Add/Remove Messages. The CTRL-V function 
is used to update variables on all displays or a specific display.

Priority Messaging will display the message number that was just 
transmitted to the display. Using this function will have precedence 
over any priority levels that are used with Add/Remove Messages. 
Add/Remove Messages will allow for up to 64 concurrently running 
messages to be shown on the display. Messages can be cleared one at 
a time or all at once. These messages can have priority levels assigned 
to them that will be used to determine how they are displayed.

The CTRL-T Function Frame

The CTRL-T function is used to trigger messages. This function 
requires an ASCII decimal value to be used to trigger the desired 
message number. The CTRL-T function has the ability for Priority 
Messaging, Add a Message, or Remove a Message. Figure 9.1 shows 
the format for the Control-T function and Table 9.1 shows the 
acceptable values.

Allen-Bradley Spares

Содержание InView Marquee 2706-P42





















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды