Allen-Bradley Compact 5000 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

Allen-Bradley Compact 5000 Скачать руководство пользователя страница 6

6

Rockwell Automation Publication 5069-IN010B-EN-P - November 2017

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Dimensions

Ground Considerations

You must ground DIN rails according to the Industrial Automation
Wiring and Grounding Guidelines, publication

1770-4.1

.

You can use the EN50022 - 35 x 7.5 mm (1.38 x 0.30 in.)

DIN rail

with Compact 5000 I/O modules.

System Power Considerations

A CompactLogix 5380 controller or Compact 5000 I/O EtherNet/IP
adapter provides power to the module.

The following power types are available:

•

Module (MOD) power

- System-side power that is required to

operate the Compact 5000 I/O modules. MOD power is
provided through the MOD power RTB and passed across the
MOD power bus.

•

Sensor/Actuator (SA) power

- Field-side power that is used to

power field-side devices. SA power is provided through the SA
power RTB and passed across the SA power bus.

The first component in the system, that is, the controller or the
adapter, establishes an SA power bus.

A system can have more than one SA power bus. You use
5069-FPD field potential distributors to establish a new SA
power bus. SA power buses are isolated from each other.

If a system includes Compact 5000 I/O modules that use AC
SA power and modules that use DC SA power, you must
install them on separate SA power buses.

ANALOG INPUT

5069-IF8

109.09 mm (4.29 in.)

25.56 mm (1.01 in.)

144.57 mm

(5.69 in.)

105.42 mm (4.15 in.)

22 mm (0.87 in.)

ATTENTION:

This product is grounded through the DIN rail to

chassis ground. Use zinc-plated chromate-passivated steel DIN
rail to assure proper grounding. The use of other DIN rail
materials (for example, aluminum or plastic) that can corrode,
oxidize, or are poor conductors, can result in improper or
intermittent grounding. Secure DIN rail to mounting surface
approximately every 200 mm (7.8 in.) and use end-anchors
appropriately. Be sure to ground the DIN rail properly. Refer to
Industrial Automation Wiring and Grounding Guidelines,
Rockwell Automation® publication

1770-4.1

for more

information.

«
...
4
5
6
7
8
...
»

Содержание Compact 5000

















Отзывы:

Нет отзывов