manualshive.com logo in svg

Allen-Bradley ArmorStart 290E, Руководство пользователя

Поделиться
Скачать
Allen-Bradley ArmorStart 290E Скачать руководство пользователя страница 158

158

Rockwell Automation Publication 290E-UM001B-EN-P - June 2012 

Chapter 5

Diagnostics

Fault Diagnostics

Fault diagnostics capabilities built in the ArmorStart LT Distributed Motor 
Controller are designed to help you pinpoint a problem for easy troubleshooting 
and quick restarting.

Protection Faults

Protection faults will be generated when potentially dangerous or damaging 
conditions are detected. Protection faults are also known as “trips” or “faults”. 
These faults will be reported in multiple formats, including: 

•

Bit enumeration in the TripStatus parameter (parameter 16) used as 
discrete bits or in DeviceLogix

•

In the ArmorStart LT web server for ArmorStart EtherNet/IP version

•

As a sequence of LED flashes on the ECM

MS – Module Status 
LED

The bicolor (green/red) LED indicates the 
status of the module.
Flashing bicolor (red/green) indicates a 
self-test on power up.

Flashing green indicates the device has not 
been assigned an IP address.
Steady green indicates the device is 
configured and operational.

Flashing red indicates a resettable 
protection fault exists or the node address 
switches have been changed without a 
power cycle and do not match the in-use 
configuration.
Steady red indicates a non-resettable 
protection fault exists.

I/O Status 
Enunciators 0…5 
LEDs

Six yellow LEDs are numbered 0…5 and 
indicate the status of the input/output 
connectors. One LED for each I/O point.

Yellow is illuminated when input is valid or 
output is on.

Off when input is not valid or the output is 
not turned on.

Reset Button

The blue reset button will cause a 
protection fault reset to occur.

—

—

Table 25 - ArmorStart LT Status and Diagnostics Indicators 

Indicator

Description

Color_1

Color_2

LED Flash

Bit Enumeration

Bulletin 290E/291E Trip Status Bits

Bulletin 294E Trip Status Bits

1

0

OverloadTrip 

➊

OverloadTrip 

➊

2

1

PhaseLossTrip

PhaseLShortTrip

3

2

UnderPowerTrip 

➊

UnderPowerTrip 

➊

4

3

SensorShortTrip 

➊

SensorShortTrip 

➊

5

4

PhaseImbalTrip

OverCurrentTrip

6

5

NonVolMemoryTrip 

➊

NonVolMemoryTrip 

➊

7

6

reserved

ParamSyncTrip 

➊

8

7

JamTrip

DCBusOrOpenDiscnnct 

➊

9

8

StallTrip

StallTrip 

➊

10

9

UnderloadTrip

OverTemperature 

➊

11

10

reserved

GroundFault 

➊

12

11

reserved

RestartRetries

13

12

reserved

DriveHdwFault 

➊

Содержание ArmorStart 290E





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды