Allen-Bradley 1788-CN2FFR Скачать руководство пользователя страница 93

Rockwell Automation Publication 1788-UM057B-EN-P - September 2014

91

Glossary

The following terms and abbreviations are used throughout this manual. 
For definitions of terms not listed here, refer to the Allen-Bradley Industrial 
Automation Glossary, publicatio

AG-7.1

.

1788-EN2FFR linking device

Provides a gateway between EtherNet/IP and a single segment FOUNDATION 
Fieldbus H1 layer. 

1788-CN2FFR linking device

Provides a gateway between ControlNet and FOUNDATION Fieldbus (FF).

AO

Abbreviation for an analog output; signal is generated by the host system and 
transmitted to a field device.

AOP

Abbreviation for Add-on Profile; provides an intuitive graphical interface for 
configuring devices.

basic device

A device that can communicate on the fieldbus, but cannot become the LAS.

block

See 

function block

resource block (RES)

, and 

transducer block

.

BOOTP

A protocol to boot a diskless workstation and receive the boot information from 
a server.

bridge

An interface in a fieldbus network that interconnects two or more H1 networks.

bus

An H1 fieldbus cable between a Host and field devices connected to multiple 
segments, sometimes through the use of repeaters.

CAS

Abbreviation for Cascade.

channel

A path for a signal.

CIP

Acronym for Common Industrial Protocol; a communication protocol, or 
language, between industrial devices. CIP provides seamless communication for 
devices on DeviceNet, ControlNet, and EtherNet/IP networks.

configurable

Capability to select and connect standard hardware modules to create a system; 
or the capability to change functionality or sizing of software functions by 
changing parameters without having to modify or regenerate software.

configuration

Physical installation of hardware modules to satisfy system requirements; or the 
selection of software options to satisfy system requirements.

connector

Coupling device used to connect the wire medium to a fieldbus device or to 
another segment of wire.

control loop

Group of function blocks that execute at a specified rate within a 
FOUNDATION Fieldbus device or distributed across the fieldbus network.

Содержание 1788-CN2FFR









































































































Отзывы: