Allen-Bradley 1788-CN2FFR Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 104

Allen-Bradley 1788-CN2FFR Скачать руководство пользователя страница 12

10

Rockwell Automation Publication 1788-UM057B-EN-P - September 2014

Preface

European Hazardous Location Approval

The following applies when the product bears the

marking.

This equipment is intended for use in potentially explosive atmospheres as
defined by European Union Directive 94/9/EC and has been found to comply
with the Essential Health and Safety Requirements relating to the design and
construction of Category 3 equipment intended for use in Zone 2 potentially
explosive atmospheres, given in Annex II to this Directive.

Compliance with the Essential Health and Safety Requirements has been assured
by compliance with EN 60079-15 and EN 60079-0.

ATTENTION:

This equipment is not resistant to sunlight or other sources of UV

radiation.

WARNING:

This equipment shall be mounted in an ATEX-certified enclosure

with a minimum ingress protection rating of at least IP54 ( as defined in
IEC60529) and used in an environment of not more than Pollution Degree 2 (as
defined in IEC 60664-1) when applied in Zone 2 environments. The enclosure
must have a tool-removable cover or door.

WARNING:

This equipment shall be used within its specified ratings defined by

Rockwell Automation.

WARNING:

Should the unit be installed in an environment where induced

transients could exceed 44V, then external transient/surge arrestors should be
installed.

WARNING:

Secure any external connections that mate to this equipment by

using screws, sliding latches, threaded connectors, or other means provided
with this product.

WARNING:

Do not disconnect equipment unless power has been removed or

the area is known to be nonhazardous.

WARNING:

Devices shall be used in an environment of not more than Pollution

Degree 2.

«
...
10
11
12
13
14
...
»

Содержание 1788-CN2FFR









































































































Отзывы:

Нет отзывов