manualshive.com logo in svg

Allen-Bradley 1757-FFLD2, Руководство пользователя

Поделиться
Скачать
Allen-Bradley 1757-FFLD2 Скачать руководство пользователя страница 148

148

Rockwell Automation Publication 1757-UM012A-EN-P - July 2011

Appendix A

        Troubleshoot the Linking Device

The table provides a description of the status indicators for channels on the 
ControlNet network that are used along with the 1757-FFLDC linking device.

Alternating red/
green

Self-test

None.

Incorrect channel 
configuration

Verify that the ControlNet network is connected to 
the correct channel of the linking device (for 
example), if the ControlNet network is configured for 
channel A only, then the linking device must be 
connected to the network via channel A).

Alternating red/off

Duplicate ControlNet 
node address

•

Choose a unique node address.

•

Cycle power to the linking device.

Table 15 - ControlNet Channel Troubleshooting (A AND B)

AND Cause

Action

Off

Channel disabled.

Use RSNetwork for ControlNet software to 
configure the ControlNet network for redundant 
media, if required.

Solid green

Normal operation

None.

Flashing green/off

Temporary network 
errors

•

Check media for broken cables, loose connectors, 
or missing terminators.

•

If condition persists, refer to the ControlNet 
Media Planning and Installation Manual, 
publication 

CNET-IN002

.

Flashing red/off

Media fault

•

Check media for broken cables, loose connectors, 
or missing terminators.

•

If condition persists, refer to the ControlNet 
Media Planning and Installation Manual, 
publication 

CNET-IN002

.

No other nodes 
present on network

Add other nodes to the network.

Flashing red/green

Incorrect ControlNet 
node address

•

Change linking device node address so that it is 
less than or equal to UMAX.

(1)

•

Cycle power to the linking device.

(1) UMAX is the highest node address on a ControlNet network than can transmit data.

Incorrect network 
configuration

Use RSNetWorx for ControlNet software to 
reconfigure the ControlNet network so that UMAX

(1)

 

is greater than or equal to the linking device’s
node address.

Table 14 - ControlNet Network Troubleshooting (A AND B)

AND Cause

Action

Содержание 1757-FFLD2

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды