Allen-Bradley 1757-FFLD2 Скачать руководство пользователя страница 131

Страница: 131 / 184

Rockwell Automation Publication 1757-UM012A-EN-P - July 2011

131

Diagnostic Web Pages

Chapter

Table 11 - Ethernet Statistics Page

Field

Description

Ethernet Link

Speed

Indicates if the Ethernet port is operating at 10 Mbps or 100 Mbps

Interface Counters

In Octets

Octets received on the Ethernet interface

In Ucast Packets

Unicast packets received on the Ethernet interface

In NUcast Packets

Non-unicast packets received on the Ethernet interface

In Discards

Inbound packets received on the Ethernet interface but discarded

In Errors

Inbound packets that contain errors (does not include In Discards)

In Unknown Protos

Inbound packets with unknown protocol

Out Octets

Octets sent on the Ethernet interface

Out Ucast Packets

Unicast packets sent on the Ethernet interface

Out NUcast Packets

Non-unicast packets sent on the Ethernet interface

Out Discards

Outbound packets discarded

Out Errors

Outbound packets that contain errors

Media Counters

Alignment Errors

Frames received that are not an integral number of octets in length

FCS Errors

Frames received that do not pass the FCS check

Single Collisions

Successfully transmitted frames that experienced exactly one collision

Multiple Collisions

Successfully transmitted frames that experienced more than one collision

SQE Test Errors

Number of times SQE test error message is generated

Deferred Transmissions

Frames for which first transmission attempt is delayed because the medium is busy

Late Collisions

Number of times a collision is detected later than 512 bit-times into the transmission of a packet

Excessive Collisions

Frames for which transmission fails due to excessive collisions

MAC Transmit Errors

Frames for which transmission fails due to an internal MAC sublayer transmit error

Carrier Sense Errors

Times that the carrier sense condition was lost or never asserted when attempting to transmit a frame

Frame Too Long

Frames received that exceed the maximum permitted frame size

MAC Receive Errors

Frames for which reception on the Ethernet interface failed due to an internal MAC sublayer receive
error

Содержание 1757-FFLD2

























































































































































































Результаты поиска

Содержание 1757-FFLD2

Отзывы:

Бренды по названию

Популярные бренды

Allen-Bradley 1757-FFLD2, Руководство пользователя

Результаты поиска

Содержание 1757-FFLD2

Отзывы:

Бренды по названию

Популярные бренды