Aileron trim
°Á·½Á
Power switch
¹·¶Ã
11
MODE 3
ª¤´¤¦
叫盢北
膘:
8
聋脸捣肞秨
ユ传北
膘家舱
ち
传
MODE 1
の
MODE 2
:巨
家Α
杆
叫猔種旧瓂よ
癸非旧瓂
抖
杆
Control sticks
±¨±¼²
SWITCHING BETWEEN MODE1 AND MODE2
SWITCHING BETWEEN MODE 3
Loosen up the 8 screws holding the two control
sticks, and swap the control sticks to change
between MODE1 and MODE2.
Pay attention to the rails when installing the control sticks.
13.LED INDICATOR
¿ ¸ » ©
This transmitter has trim memory capability.
When the control stick modes are changed,
all trims are retained so there is no need to
re-trim.
¥» ±¾ ¨³ °¾ ¥¯ ¡ ·±¤´ ¾ ±¼ ¦ ® ¡ » ±¾
·¦ °±±¥ª ·½ ¼ ¾ « ¯ ¨¤´ ¡ ¤» ·½ ¾ ¡
MODE 1
»
MODE 2
ª¤´¤¦
ª ·
CAUTION
虫も
╂
盢捌羖
よ
搽:稬秸龄┕い丁崩帝ぃ
钡帝
も盢筿方秨闽┕
崩秨筿方
换北竟
穦祇
"
雇
"
x
mボ秈
MODE 3
狾
MODE 1
MODE2
ぃ陪ボ
ち传
MODE 3
Θ
换北竟穦癘拘
MODE 3
–Ω
秨诀常穦
"
雇
"
x
璝璶ち传
MODE 1
璶
狡
Ω
瓃:笆
换
北竟穦祇
"
雇
"
祏
mボp
MODE 1
ち传
MODE 1
Θ
换北竟穦癘拘
MODE 1
–Ω
秨诀常穦
"
雇
"
祏
To change MODE setting back to MODE1, just
repeat the above procedure. Transmitter will emit
a short beep indicating MODE1 has been set.
After transmitter is switched to mode 3, the mode
will be retained every time when powered up, as
indicated by a long beep.
Using thumb and pointer fingers, hold the aileron
and rudder trim tabs toward the middle while
turning on the transmitter power. Transmitter will
emit a long beep indicating MODE3 has been set.
However, both MODE1 and MODE2 will not be
indicate on the transmitter screen.
Rudder trim
¤¦²·½Á
After transmitter is switched to MODE 1, the
mode will be retained every time when powered
up, as indicated by a short beep.
MODE 3
¥¶¦
MODE 1
¼¦¤¤¯¤´³©¡
MODE 3
ªªª·±¦¼¬¦¥¤Ãª¦¸¡
MODE3 setting needs to be set with the control sticks in MODE1 position,
which means throttle is on the right hand side.
ª ·
CAUTION
Green
º¿
Red
¬
Blue
Â
¿¸Å¥
ªª«¥
¶¾ª©¤
Power on Initializing
LED
§³°Ã
4
¬
LED Fast flashing 4 seconds.
¹À¦¥
Binding successful
««
steady lit
¹À¥±
Binding failed
º³³°
Slowly single flash
§¹ÀÄ¥
Voltage warning
LED status
°
Double Flashes