background image

 

 

 

 

WARNING 

 

Read the OPERATION MANUAL before operating this equipment. 

DISCLAIMER  

Algas-SDI International, LLC (ASDI) shall not be liable for technical 
and/or editorial errors or omissions in this manual.  ASDI makes no 
warranties, express or implied, including the implied warranties of 
merchantability and fitness for a particular purpose with respect to 
this manual.  In no event shall ASDI be liable for any special or 
consequential damages including, but not limited to loss of 
production time, or loss of profits. 

   NOTE:   Algas-SDI reserves the right to use alternate manufacturers’ 

components as vendor delivery applicability dictates.  Vendors 
have supplied literature contained in the Operation Manual.  
Please check to be sure supplied data matches your 
configuration.  Contact Algas-SDI if any questions exist. 

   This equipment uses LPG-a flammable fuel, or NH3-a toxic gas, 

(depending on the model), handled under pressure.  Inherent hazards 
exist, and a thorough understanding of the equipment is required to 
allow safe operation and maintenance. 

   Allow only a TRAINED and FULLY QUALIFIED PERSON to service this 

equipment. 

   Any time a component must be replaced, use the same type, model, etc.  

DO NOT SUBSTITUTE!  The consequences from such actions are 
unpredictable and may lead to dire consequences.  When components 
are replaced with components not approved for use in our FM/CSA 
listed equipment, the FM/CSA listing becomes void for that unit. 

 

Содержание VAPORAIRE M-Series









































































Отзывы: