background image

AX400 / AE 500 H First Edition

Owner

s Manual

Thank you for purchasing our receiver

For proper use of this receiver, please read this manual thoroughly.

Keep this manual in a safe place for future reference.

WARNING

l

 

Do not use any batteries other than size AA Alkaline or manganese batteries. Using different batteries could

cause fire, electric shock or failure.

l

 

Do not place consumed batteries in a fire. They could explode, causing fire or burns.

l

 

Do not install or remove batteries while your hands are wet. This could cause electric shock.

l

 

In the event that smoke is emitted, a strange odor or noise is generated, or similar abnormality occurs, it could

cause fire, electric shock or breakdown. Consult your dealer immediately for the necessary instructions or

repair needed.

l

 

Do not attempt to repair the receiver yourself. Doing so may lead to serious damage or physical injury.

l

 

Do not attempt to disassemble or modify this product in any way.  This could lead to fire, electric shock or

breakdown.

CAUTION

l

 

Do not use this product for anything other than a receiver.

l

 

When not in use, keep it out of the reach of infants and small children.

l

 

During extended trips or other times when this product is not in use for long periods, take the batteries out.

Keep the batteries stored in a safe place and out of the reach of infants and small children.

l

 

Discontinue use of this product if it has a negative influence on TV, electronic device, therapeutic devices and

or other equipment.

l

 

Always be aware of antenna location to avoid personal injury.

l

 

When conducting routine maintenance, be sure to disconnect the power for additional safety.

l

 

Do not place this product in locations with extreme temperature, high humidity or excessive dust.  Do not keep

it in an automobile.  It could lead to fire, electric shock or breakdown.

NOTICE

Unauthorized use of the contents of radio communications or divulging its contents to other parties is prohibited by

law.

INTRODUCTION

Содержание AE 500 H



















Отзывы: