manualshive.com logo in svg

Alarm SAF BN10-000-UL, Руководство по эксплуатации и установке

Поделиться
Скачать
Alarm SAF BN10-000-UL Скачать руководство пользователя страница 36

3.3 ABC Connectors and Harnesses

3.3.1  The ABC buss supplies the voltages (B1 and B2) and FAI control to compatible 
accessory boards.  B1 is supplied through pins 5 and 6 while B2, if used, is supplied
through pins 7 and 8 of each connector.  By using the appropriate cables, one or two
independent voltage sources can be connected to the PD8(F) for distribution to it’s
outputs.

3.3.2  Single Voltage Distribution

A single power source can be connected to the PD8(F) by using a white 6-6 cable
(AS Part Number A099052) connected to pins 1 through 6 of one of the ABC
connectors (P1 or P2).

3.3.3  Dual Voltage Distribution

3.3.3.1  If both source voltages are present on the ABC buss, use a brown 8-8 cable
(AS Part Number A099068 or A099069) connected to either ABC Connector to
provide both B1 and B2.
3.3.3.2  If two independent supplies are used, a white 6-6 cable is needed for B1 
on either ABC connector, and a red 6-8 cable is needed for B2 on the other ABC
connector.

3.3.4  Cable Types

ABC-06

18 inches

Red

A099071

6-8

ABC-05

8 inches

Red

A099070

6-8

ABC-04

18 inches

Brown

A099069

8-8

ABC-03

8 inches

Brown

A099068

8-8

ABC-02

18 inches

White

A099063

6-6

ABC-01

8 inches

White

A099052

6-6

Description

Length

Color

AS PN

Cable Type

ABC-01

Used to connect a Beacon power supply to the first accessory board, when
the ABC slot is used or accessory board is located close to power supply.

ABC-02

Used to connect a Beacon power supply to the first accessory board, when
the ABC slot is used or accessory board is not located close to power supply.

ABC-03

Used to connect accessory board to accessory board over short distances.

ABC-04

Used to connect accessory board to accessory board over long distances.

ABC-05

Short cable used to connect two Beacons to single accessory board for high
power dual voltage systems.

ABC-06

Long cable used to connect two Beacons to single accessory board for high
power dual voltage systems.

PD8(F) Installation Instructions
10/27/2006, 1:58:40 PM

52-326 Rev B.01

Page 7 of 14

AlarmSaf

 65A Industrial Way, Wilmington, MA 01887 978 658 6717 www.alarmsaf.com

Содержание BN10-000-UL












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды