r
Quick Start
First Time Start Up
1. Unpack the lock.
2. W ith the batteries disconnected, hold down the
key for 10 seconds and release.
3. Connect the batteries and listen for 3 beeps. W ithin 5 seconds of hearing the 3 beeps, press and hold
until beeping
starts. This will clear the lock of all programmed data. Important: If you do not hear these 3 beeps, you must start over at
step
2
.
4. Listen for another series of beeps and LED flashes
followed b y 10 seconds o f silence.
The lock is now ready to program.
Failure to follow this exact procedure can result in erratic lock behavior. Im p o rta n t Note:
W hen entering any key se
quence below,
do not pause m ore than 25 seconds between any ke y
presses--otherwise you must start again.
Enter Program Mode and Change Factory Master Code
1. P ress th e d e fa u lt M a ste r C ode: I I ^ D l 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 .
2. W a it fo r th e green lig h t and press 1 1 ^ 3 until m ultiple b e e p s are heard. Y ou are n o w in Program M ode.
N ote:
The lock w ill beep e ve ry
6
se co n d s as a re m in d e r th a t you are in P rogram M ode.
3. E n te r a n e w perso n a l
6
-d ig it M a ste r C ode n u m b e r b y pressing th e fo llo w in g keys:
1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 [new Master Code] 1 1 ^ 3 [new Master Code] 1 1 ^ 3 (the se cond se t o f digits m u st be e xa ctly the sam e).
(F o r e xam ple, if you w a n t yo u r n e w M a ste r C ode to be “6 6 4 4 3 3 ” . Press:
D
D
D
m
i i c s p i i i c o i m
m
m
m
m
u c s p i i i c o i m
m
m
c
v
N o w th a t the M aster C ode has been changed, there is no need to change it again (unless you w ant to). Since you are
still in Program Mode, you can now proceed directly below and program various functions.
Note:
P rogram m ing any
Function, such as setting the clock, follows a consistent 5-step pattern: (1) Enter Program Mode (2) Press 1 1 ^ 3
[Function #] (3) Press 1 1 ^ 3 and enter data (4) Press 1 1 ^ 3 to end (5) Exit P rogram Mode.
Note: There is a 3 minute Program Mode timeout if no keys are pressed when in Program Mode. A steady tone will sound
for the final 15 seconds of the 3 minute timeout period as a warning. To remain in Program Mode, press any key.
Note: To prevent possible date and time changeover issues, avoid entering program mode at or near midnight.
Set the Weekday
1. E n te r P rogram M ode (if not in already).
2. P ress 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 [number of weekday] 1 1 ^ 3 . (U se 1= S unday, 7 = S aturday).
(F o r e xa m p le - Friday - p re ss 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 ).
Set the Date
1. E n te r P rogram M ode (if not in already).
2. P ress 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3
[
m m d d y y
]
1 1 ^ 3 .
(F o r e xa m p le - M ay 10, 2 002 - press 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^3 1 1 ^3 1
1 1 ^ 3 ).
Set the Time
1. E n te r P rogram M ode (if not in already. If you ju s t fin ish e d th e above p rocedure, you are still in P rogram M ode).
2. P ress 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3
[
h h m m
]
1 1 ^ 3 . (U se 2 4 -h o u r m ilita ry fo rm a t, w h e re PM adds 12 hours).
(F o r e xa m p le - 2 :30pm - press 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 l l ^ 3 l l ^ 3 l l ^ 3 ^ ^ ^ 1 1 ^ 3 ).
Enter User Codes
1. E n te r P rogram M ode (if not in already).
2. P ress
[User Number]
[new User Code] l l^ ^ ^ l.
(F o r e xam ple, John S m ith is d e sig na te d as U se r 21. Y ou w a n t him to use th e code o f “2 3 2 3 2 3 ” to u n lo ck th e door.
P rogram th e lock by p ressing: 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 1 1 ^ 3 l l ^ 3 l l ^ 3 l l ^ 3 ^ ^ 3 ^ 3 ^ ^ ^ 1 1 ^ 3 ).
3. R e p e a t step 2 fo r each n e w user.
Delete a User Code
1. Enter Program Mode (if not in already).
12