You must be in the Program Mode.
In the event a User Code must be deleted do the following, press the Location Number then
enter the User Number then press the key. The Yellow Led will flash twice and you will
hear two beeps. The selected User Code has been deleted.
Output 1 in Momentary Mode
You must be in the Program Mode.
Press the keys then enter the relay “on” time. This time can be from 1 to 999 sec.
then press the key. The Yellow Led will flash twice and you will hear two beeps.
The
Momentary Mode for Output 1 has been entered.
Output 1 in Latching Mode
You must be in the Program Mode.
Press the keys. Follow the directions above to enter Output 1 Latching Mode but
do not enter the relay “on” time.
You must be in the Program Mode
The User Codes can be from 4 to 8 digits in length, (digits can be repeated).
The User Codes must not be the same as the Installer Code !
User Codes Group 1 - There are 100 User Codes in Group 1
Group 1 operates Relay 1
User Codes Group 2 - There are 10 User Codes in Group 2
Group 2 operates Relay 2
TO PROGRAM GROUP 1
Press the key then enter the User Number, this number is two digits long and ranges
from
00
to
99
, then enter the user code, then press the key. The Yellow Led will
flash twice and you will hear two beeps.
TO PROGRAM GROUP 2
Press the key then enter the User Number, this number is one digit long and ranges
from
0
to
9
, then enter the user code, then press the key. The Yellow Led will
flash twice and you will hear two beeps.
PAGE 10
PAGE 5
STEP 2 KEYPAD INITIATION MODE
The Keypad Initiation Mode 1 allows 100 user codes in code lengths from 4 to 8 digits with
more than 100 million code combinations.
THIS PROCEDURE MUST BE FOLLOWED !
To activate Keypad Initiation Mode enter then press the key. The Yellow
Led will flash twice and you will hear two beeps. You are now in
Keypad Initiation Mode.
8 9 0 1
STEP 3 ENTERING THE USER CODES
#
1
2
#
#
EXAMPLE OF ENTERING A FOUR DIGIT USER CODE
LOCATION
USER NUMBER
USER CODE
TO ENTER PRESS
DELETING A USER CODE
CONFIGURATION OF OUTPUT MODES
1
2
0 2
3
4 0
5 3 8 1
6 4 9 2
#
#
#
#
BASIC WIRING OF AN INTER-LOCK SYSTEM USING TWO KEYPADS
DOOR 2
CONTACT
DOOR 1
CONTACT
DOOR 1
DOOR 2
EGRESS STATION
OPENS DOOR 1
FROM INSIDE
EGRESS STATION
OPENS DOOR 2
FROM INSIDE
MAGNETIC
LOCK
OR
ELECTRIC
STRIKE
MAGNETIC
LOCK
OR
ELECTRIC
STRIKE
MODEL KP-400
MODEL KP-400
An Inter-lock system requires two Keypads. This application example uses two KP-400
with simple cross wire connections to their Output Inhibit & Inter-lock Control Output.
It is necessary to connect the GND, (-), terminals of the two Keypads as a common
ground to achieve the Inter-lock function.
Use the Keypad to open the door from the outside. Use the Egress station to open the
door from the inside. Connect the magnetic door contacts on the door to monitor their
position. When Door 1 is open, then Door 2 remains locked, or vice versa.
WHEN WIRING AN ELECTRIC STRIKE
The 1N4004 diode must be connected to the Electric Door Strike as shown in the dia-
gram above to prevent arcing across the Keypad relay contacts. The diode is not re-
quired when powering the Electric Door Strike on AC current. Use the N/O Output when
operating the Electric Strike in the fail-secure mode. Use the N/C Output when operat-
ing the Electric Strike in the fail-safe mode.
CROSS WIRE CONNECTIONS FOR INTER-LOCK
MODEL
TS-2
SHOWN
MODEL
TS-2
SHOWN
4 1
12 OR 24
AC OR DC
POWER
SUPPLY
12 OR 24
AC OR DC
POWER
SUPPLY
AC CAN ONLY
BE USED WITH
ELECTRIC STRIKES
AC CAN ONLY
BE USED WITH
ELECTRIC STRIKES
REMOVE
FACTORY
INSTALLED GND
JUMPER
FROM EACH KEYPAD
