en
Safety instructions
12
351 - 1201 Plus
type series plus
351
501
901D
901
1201
Strap (not permitted for lifting)
Minimum breaking force (F
min
)
Drum capacity (m)
42 x 1
9 kN
4 m
42 x 1
12,5 kN
7 m
52 x 1.4
22,5 kN
10 m
52 x 1.4
22,5 kN
10 m
55 x 1.6
30 kN
12,5 m
Minimum load (kg)
25 kg
25 kg
25 kg
25 kg
25 kg
Permissible ambient temperature
- 20 °C to + 50 °C
* in accordance with EN 12385-4 (rope class 6x19 / 6x19 M / 6x19W - / WRC)
** acc. to DIN EN 13157 (7-times safety for the strap required)
SAFETY INSTRUCTIONS
CAUTION!
Danger due to brake being released!
Jolting can cause the load pressure
brake to be released. Do not use the
winch for securing loads! Do not remove
the crank handle under load!
Danger to life and limb! - Never stand under
suspended loads!
Risk of accident! - Lowering loads over pro-
longed periods may cause the braking sys-
tem to become hot. Observe cooling breaks!
➯
Depending on the load, the maximum lo-
wering duration is 2 - 5 minutes.
Only use ropes whose hooks are attached
with a pressed rope loop. End connections
acc. to EN 13411-3 with thimbles acc. to
13411-1.
➯
Unless specified otherwise in the afore-
mentioned EN standards, the cable end
connections must withstand a force of at
least 85% of the minimum breaking force
of the cable without breaking.
Hook and connecting device (triangle) must
offer 4-times safety with cables and straps.
No permanent distortion is allowed under sta-
tic load with 2-times the nominal load. At 4-ti-
mes static load, bending open or deformation
is permitted, however the load must still be
securely held (see EN 13157). Alternatively,
a hook acc. to EN 1677-2 with guaranteed
safe working load must be used.
Sharp edges! Risk of abrasion, crushing,
cuts. Always wear protective gloves.
If using a strap - observe the required brea-
king force.
➯
The breaking force of the stitched strap
must be at least 7 times the specified ten-
sile force in the lowest cable position.
Do not allow the rope/strap to knot.
Do not expose straps to acids or alkalis.
Protect straps against moisture and perma-
nent exposure to sunlight by means of a co-
ver.
Do not exceed the tensile forces specified in
the technical data.
Always used non-twisting or low-twisting ro-
pes for lifting a freely suspended load that
could rotate during the lifting procedure!
ASSEMBLY
Assembling the crank handle
ADVICE
The crank handle must be able to make
at least a ¼ turn to the left without moving
the drive shaft or the rope drum.
Use a torque wrench for tightening. Tigh-
tening torque 20Nm.
Typ 351 Plus, 501 Plus, 901 Plus, - Standard
1. Remove the hexagon head screw, spring lock
washer and washer from the drive shaft (
1-1
).
2. Hold the cable drum firmly and screw on the
crank/crank nut fully.
3. Putting spring washer and plate on (
2-1
).
4. Screw in the screw anticlockwise until fin-
ger-tight (
2-1
).
5. Hold the crank/crank nut firmly and tighten the
screw with a torque wrench.
6. Check if the crank/crank nut can be moved.
7. Push the cover on (
2-2
).
Type 901 Plus D - double crank handle
1. Push crank handle onto the drive shaft (
3-1
).
2. Insert the locking pin.
3. Push crank handle onto the drive shaft at 180°
to crank handle (
3-2
).
4. Insert the locking pins.
Содержание 1201 Plus
