AJ Aircraft Raven 73" Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 26

background image

aj-aircraft.com

Page 18

Align the rudder hinges to the vertical stabilizer hinges.
Insert the rudder hinge pin through the top of the rudder
then through each of the hinges.

Insert the rudder servo into the fuselage pocket with the
drive spline towards the front of the fuselage. The holes
for the servo mounting screws are pre drilled. Install the
servo with the wood screws that came with your servos.
Remove the screws and servo and apply a drop of thin CA
glue into each mounting screw hole. This will harden the
wood around the screws and provide a more secure
installation. (Allow the CA glue to dry before reinstalling
the servo.)

Tread the brass cable eyes about half way into the ball
links.

Start the cable assembly at the servo end inside the
fuselage. Thread on 2 crush sleeves and the brass cable
eye. (Many people also thread on some heat shrink tube
to cover the assembly to give a finished look.)

Loop around the cable eye and go back through the first
crush sleeve.

Loop around the first crush sleeve and back through the
sleeve again. Slide the second sleeve over the tail.

Adjust the loops and crimp the sleeves with the non-
serrated surface plyers.

«
...
17
18
19
20
21
...
»

Содержание Raven 73"



























Отзывы:

Нет отзывов

Похожие инструкции для Raven 73"

Kittyhawk Mk.Ia

Бренд: Eduard Страницы: 3

minideices 17865

Бренд: Lansay Страницы: 2

St. Canute "700"

Бренд: Billing Boats Страницы: 28

Бренд: marklin Страницы: 24

Rudolph the Rocking Reindeer 4827

Бренд: Step2 Страницы: 4

Бренд: Mega Bloks Страницы: 32

Бренд: Ripmax Страницы: 20

Бренд: Wrebbit Страницы: 40

Бренд: Faller Страницы: 4

Jungle Gym: Step & Count Kangaroo

Бренд: VTech Страницы: 11

DESIGNER'S CHOICE 30 MODEL BUILDING SET

Бренд: K'Nex Страницы: 52

FIELD TRACK CROSSING

Бренд: Faller Страницы: 4

No. 9 pay as you enter

Бренд: M.T.H. Страницы: 23

Fishbellied bridge

Бренд: Faller Страницы: 4

Бренд: Fisher-Price Страницы: 16

Бренд: Horizon Hobby Страницы: 12

Бренд: THE WORLD MODELS Страницы: 20

Volkswagen Beetle LED Lighting Kit

Бренд: LIGHT MY BRICKS Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды