AJ Aircraft Raven 73" Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 26

background image

aj-aircraft.com

Page 16

We suggest using 30 minute epoxy for the elevator
jointer plate and polyurethane glue for the hinges. (Add
a drop of water to each hinge hole if using polyurethane
glue like

Gorilla Glue

. This type of glue activates with

moisture.)

•

Begin the final assembly of the elevator by adding
glue to the horizontal stabilizer hinge holes then
insert hinges. (If using

Gorilla Glue

it will only take a

few drops per hinge. Use a pin to push the glue into
the hole.)

•

Add epoxy to the joiner slot and glue to the hinge
holes of one half of the elevator then partially slide it
onto the hinges.

•

Insert the jointer plate through the fuselage then into
the elevator half.

•

Add epoxy to the joiner slot and glue to the hinge
holes of the second elevator half then slide it onto
the hinges and jointer plate.

•

Push both elevator halves into position and wipe
away any epoxy that has squeezed out.

•

Watch for glue expanding around the hinges and
wipe away with alcohol as needed.

•

Move the elevator up and down to make sure it has
full travel.

It won’t hurt to apply additional

petroleum jelly to the hinges.

•

Tightly tape the gap between the horizontal stabilizer
and the elevator counter balance while the glue and
epoxy dry.

Carefully remove

“

masking

”

tape before the epoxy fully

sets. But do not remove the tape at the stabilizer and
elevator counter balance until epoxy is fully cured.

Attach a 24” servo extension onto the elevator servo lead

and use shrink wrap or a safety clip to secure the
connection.

Connect the elevator servo to a receiver and power
supply. Turn on your transmitter. Set trim and sub trim
to zero. Install a servo arm on the servo approximately

perpendicular to the servo side. Use the transmitter’s

sub trim to make it perpendicular.

«
...
15
16
17
18
19
...
»

Содержание Raven 73"



























Отзывы:

Нет отзывов

Похожие инструкции для Raven 73"

Бренд: Bachmann Страницы: 2

MC FIZZ FIZZY BALLS

Бренд: Jamara Страницы: 4

Бренд: Spin Master Страницы: 4

EXTRA 330SC 60CC

Бренд: AeroPlus Страницы: 19

Бренд: Eduard Страницы: 4

Бренд: MTHTrains Страницы: 36

Clickables Fairy Charms IM-21300B

Бренд: Techno Source Страницы: 1

Бренд: E sky Страницы: 32

Toot-Toot Drivers Press ‘n’ Go Vehicle

Бренд: VTech Страницы: 3

Бренд: VTech Страницы: 18

Бренд: VTech Страницы: 2

Бренд: MODSTER Страницы: 21

Peek At Me Bunny

Бренд: VTech Страницы: 10

Бренд: marklin Страницы: 32

Бренд: QuickWorldWide Страницы: 53

Бренд: Mega Bloks Страницы: 2

Smart Start Future

Бренд: VTech Страницы: 16

Бренд: Smoby Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды