Aiwa XR-MD200 Скачать руководство пользователя страница 50

Страница: 50 / 72

IC, CXD2652AR

Pin No.

Pin Name

I/O

Description

MNT0

MNT1

MNT2

MNT3

SWDT

SCLK

XLAT

SRDT

SENS

XRST

SQSY

DQSY

RECP

XINT

OSCI

OSCO

XTSL

DVSS

DIN

DOUT

ADDT

DADT

LRCK

XBCK

FS256

DVDD

A03

A02

A01

A00

A10

A04

A05

A06

A07

Monitor output terminal.

Microprocessor serial interface data input.

Microprocessor serial interface shift clock input.

Microprocessor serial interface latch input. Latched at falling down edge.

Microprocessor serial interface data output.

The terminal which outputs internal status in accordance with the address of the

microprocessor serial interface.

Reset input. L: reset.

Disc sub code Q sync/ADIP sync output.

Subcode Q sync output of U-bit CD or MD format when the DIGITAL IN source is

CD or MD.

Laser power selection input. H: Recording power, L: Playback power.

Interrupt request output terminal. L is output when interrupt status is generated.

Record data output enable signal input terminal. H: enable.

Crystal oscillator circuit input terminal.

Crystal oscillator circuit output terminal. (Inverted output of OSCI).

OSCI terminal input frequency selection. H: 512 Fs (22.5792 MHz), L: 1024 Fs

(45.1584 MHz).

Not connected.

Digital GND.

Digital audio interface signal input.

Digital audio interface signal output.

Analog recording signal input terminal. (External A/D converter output is connected to

this terminal).

RECORD monitor output/decode audio data output.

LRCK (44.1 kHz) output terminal to external audio block.

Bit clock output (2.8224 kHz) output terminal to external audio block.

256 Fs output. (11.2896 MHz).

Digital power supply.

Address output to external DRAM.

Address output to external DRAM. (Not used).

Address output to external DRAM.

—

Содержание XR-MD200









































































Результаты поиска

Содержание XR-MD200

Отзывы:

Похожие инструкции для XR-MD200

Бренды по названию

Популярные бренды

Aiwa XR-MD200, Руководство по обслуживанию

Результаты поиска

Содержание XR-MD200

Отзывы:

Похожие инструкции для XR-MD200

Бренды по названию

Популярные бренды