En-3
3.2. Installation dimension
Ceiling height is as shown in the figure.
Strong and durable ceiling
3,000 mm or more
1,800 mm to
H
1,000 mm or more
Floor
Obstruction
1,500 mm
or more
256 mm or more (AUXM018,024,030)
298 mm or more (AUXK018,024,030,034,036,045,054)
H: Maximum height from floor to ceiling
Function setting
H (mm)
AUXM
018/024/030
AUXK
018/024/030/034
AUXK
036/045/054
Standard
mode
3,000 3,200 3,200
High Ceiling mode
3,500
3,600
4,200
* Be sure to make the function settings with the remote controller according to the
installed ceiling height.
Discharge direction setting
• The discharge direction can be selected as shown below.
4 direction
3 direction
100 mm or more *1
*1: Please ensure sufficient
service access during
installation.
* Select the most appropriate airflow direction from 3 or 4 directions according to the
shape of the room and the installation position.
* When changing the number of outlets, we recommend using the optional AIR OUTLET
SHUTTER PLATE KIT to close the outlet.
* For the specific closing pattern, please refer to the attached AIR OUTLET SHUTTER
PLATE KIT’S MANUAL. (Do so before installing the cassette grille as it will be installed
on the body.)
3.3. Installing the unit
WARNING
Install the air conditioner in a location which can withstand a load of at least 5 times the
weight of the main unit and which will not amplify sound or vibration. If the installation
location is not strong enough, the indoor unit may fall and cause injuries.
If the job is done with the panel frame only, there is a risk that the unit will come loose.
Please take care.
3.3.1. Position the ceiling hole and hanging bolts
(1) Positions of the ceiling opening, hanging bolt pitch, piping and ducts.
• Ceiling opening and hanging bolt pitch. (unit: mm)
950 (Cassette grille)
860 to 910 (Ceiling opening)
840 (Indoor unit)
796 (Hanging bolt pitch)
20 to 45
20 to 45
20 to 45
20 to 45
130
130
130
768 (Hanging bolt pitch)
950 (Cassette grille)
860 to 910 (Ceiling opening)
840 (Indoor unit)
200
130
50
A
B
50 to 100
10
39
200 to 205
Type
Dimension (mm)
A
B
AUXM
246
256
AUXK
288
298
• Refrigerant piping and drain piping positions. (unit: mm)
Drain pipe
(Connect the attached
drain hose)
342
293
45
200
140
180
10
80
Gas pipe
Liquid pipe
Drain pipe
• Distribution ducts and fresh air inlet positions.
Distribution duct
connecting port
Distribution duct
connecting port
Fresh air
inlet position
Distribution duct
connecting port
Distribution duct connecting port
Drain pipe
Refrigerant pipe
10 × Ø 3.2 hole
100
100
352
83
83
Cut out
90
163
Detailed diagram of distribution duct con-
necting port (4 sides)
250
4 × Ø 3.2 hole
Ø 70
(cut out)
Ø 144
(bolt pitch)
163
Fresh air inlet position
NOTE:
Conduct proper insulation when connecting the
distribution ducts and fresh air inlet.
* When sucking in the fresh air, please detach the
insulation affixed to the drain pan.
Fresh air
inlet position
Insulation
(2) Setting the positions of hanging bolt and
ceiling opening.
• Use an installation template (packaging top
surface) to set the positions of the hanging bolt
and ceiling opening and drill holes.
(3) Hanging
structure.
• Select a strong structure for the hanging location.
• If necessary, reinforce the hanging bolt with quakeproof columnar support material to
prevent shaking.
• Use hanging bolts of M8 to M10.
3.3.2. Hanging preparations
• Firmly fasten the hanging bolts as shown
in the figure or by another method.
• Install the hanging bolts at a place
where they would be capable of holding
a weight of at least 490 N per bolt.
Hole-in anchor
Hole-in plug
Concrete
Insert
Hanging bolt M10
(locally purchased)
3.3.3. Body installation
WARNING
Perform final tightening by tightening the double nut firmly.
Be sure to install the body horizontally and adjust the height below the body and the
ceiling surface properly.
(1) Install the attached
washer and nut (prepared
on site) onto the hang-
ing bolt.
(2) Hook the body onto the
hanging bolt.
(3) Adjust the dimensions of
the ceiling surface from
the body.
After installing the
cassette grille, you can
make fine adjustment of
the height of the body.
For details, refer to the
installation manual of the
cassette grille.
Hanging bolt
(locally purchased)
Nut A
(locally purchased)
Washer
(Accessories)
Washer
(Accessories)
Nut B (Double Nut)
(locally purchased)
30 mm or more
10 to 15 mm
After installing
the body, tighten
the nuts.
9371022642-02_IM.indb 3
9371022642-02_IM.indb 3
2019/10/11 10:00:39
2019/10/11 10:00:39
