AirStage ARXD07GALH, Руководство по установке

Страница: 2 / 180

En-1
1. SAFETY PRECAUTIONS
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information
pertaining to your safety. Be sure to observe them.
• Hand this Manual, together with the Operating Manual to the customer.
Request the customer to keep them on hand for future use, such as for relocating or
repairing the unit.
WARNING
This mark indicates procedures which, if improperly performed,
might lead to the death or serious injury of the user.
Request your dealer or a professional installer to install the unit in accordance with this
Manual.
An improperly installed unit can cause serious accidents such as water leakage,
electric shock, or
fi re.
If the unit is installed in disregard of the instructions in the Installation Manual, it will
void the manufacturer’s warranty.
Do not turn ON the power until all work has been completed.
Turning ON the power before the work is completed can cause serious accidents such
as electric shock or
fi re.
If refrigerant leaks while work is being carried out, ventilate the area.
If the refrigerant comes in contact with a
fl ame, it produces a toxic gas.
Installation work must be performed in accordance with national wiring standards by
authorized personnel only.
Except for EMERGENCY, never turn off main as well as sub breaker of the indoor units
during operation. It will cause compressor failure as well as water leakage.
First, stop the indoor unit by operating the control unit, converter or external input
device and then cut the breaker.
Make sure to operate through the control unit, converter or external input device.
When the breaker is designed, locate it at a place where the users cannot start and
stop in the daily work.
CAUTION
This mark indicates procedures which, if improperly performed,
might possibly result in personal harm to the user, or damage to
property.
Read carefully all security information before use or install the air conditioner.
Do not attempt to install the air conditioner or a part of the air conditioner by yourself.
This unit must be installed by qualified personnel with a capacity certificate for handling
refrigerant fluids. Refer to regulation and laws in use on installation place.
The installation must be carried out in compliance with regulations in force in the place
of installation and the installation instructions of the manufacturer.
This unit is part of a set constituting an air conditioner. It must not be installed alone or
with non-authorized by the manufacturer.
Always use a separate power supply line protected by a circuit breaker operating on all
wires with a distance between contact of 3mm for this unit.
The unit must be correctly grounded and the supply line must be equipped with a
differential breaker in order to protect the persons.
The units are not explosion proof and therefore should not be installed in explosive
atmosphere.
Never touch electrical components immediately after the power supply has been turned
off. Electric shock may occur. After turning off the power, always wait 5 minutes before
touching electrical components.
This unit contains no user-serviceable parts. Always consult authorized service
personnel to repairs.
When moving, consult authorized service personnel for disconnection and installation of
the unit.
2. ABOUT THE UNIT
2.1. Precautions for using the R410A refrigerant
WARNING
Do not introduce any substance other than the prescribed refrigerant into the
refrigeration cycle.
If air enters the refrigeration cycle, the pressure in the refrigeration cycle will become
abnormally high and cause the piping to rupture.
If there is a refrigerant leakage, make sure that it does not exceed the concentration
limit.
If a refrigerant leakage exceeds the concentration limit, it can lead to accidents such as
oxygen starvation.
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
area. Touching the refrigerant directly can cause frostbite.
If a refrigerant leakage occurs during operation, immediately vacate the premises and
thoroughly ventilate the area.
If the refrigerant comes in contact with a
fl ame, it produces a toxic gas.
2.2. Special tool for R410A
WARNING
To install a unit that uses the R410A refrigerant, use dedicated tools and piping
materials that have been manufactured speci
fi cally for R410A use.
Because the pressure of the R410A refrigerant is approximately 1.6 times higher than
the R22, failure to use dedicated piping material or improper installation can cause
rupture or injury.
Furthermore, it can cause serious accidents such as water leakage, electric shock, or
fi re.
Contents
1. SAFETY PRECAUTIONS ......................................................................................... 1
2. ABOUT THE UNIT .................................................................................................... 1
2.1. Precautions for using the R410A refrigerant ...................................................... 1
2.2. Special tool for R410A ....................................................................................... 1
2.3. Accessories ....................................................................................................... 2
2.4. Optional parts .................................................................................................... 2
3. INSTALLATION WORK ............................................................................................ 3
3.1. Selecting an installation location ....................................................................... 3
3.2A. Installation dimensions (Ceiling concealed type) ............................................ 3
3.2B. Installation dimensions (Wall mounted type/Floor standing concealed type) ..... 3
3.3A. Installation the unit (Ceiling concealed type) ................................................... 3
3.3B. Installation the unit (Wall mounted type/Floor standing concealed type) ........ 5
4. PIPE INSTALLATION ............................................................................................... 7
4.1. Selecting the pipe material ................................................................................ 7
4.2. Pipe requirement ............................................................................................... 7
4.3. Flare connection (Pipe connection) ................................................................... 7
4.4. Installing heat insulation .................................................................................... 8
5. INSTALLING DRAIN PIPES ..................................................................................... 8
5.1A. When drain pump is used ............................................................................... 8
5.1B. When drain pump is not used (Natural drainage) ...................................................8
5.2. Install the drain pipe .......................................................................................... 9
6. ELECTRICAL WIRING ........................................................................................... 10
6.1. Electrical requirement ...................................................................................... 11
6.2. Wiring method ................................................................................................. 11
6.3. Unit wiring ........................................................................................................ 11
6.4. Connection of wiring ........................................................................................ 12
6.5. External input and external output (Optional parts) ......................................... 13
6.6. Remote sensor (Optional parts) ...................................................................... 15
6.7. IR receiver unit (Optional parts) ....................................................................... 15
6.8. Auto louver grille (Optional parts) .................................................................... 15
6.9. Optional parts cable binding ............................................................................ 16
7. FIELD SETTING ..................................................................................................... 16
7.1. Setting the address .......................................................................................... 16
7.2. Custom code setting ........................................................................................ 17
7.3. Static pressure mode ....................................................................................... 17
7.4. Switching of drainage function ......................................................................... 17
7.5. Switching of air
fl ow direction louver function ................................................... 17
7.6. Switching the upper limit of cooling temperature ............................................. 18
7.7. Function setting ............................................................................................... 18
8. TEST RUN .............................................................................................................. 18
8.1. Test run using Outdoor unit (PCB) .................................................................. 18
8.2. Test run using Remote Controller .................................................................... 18
9. CHECK LIST ........................................................................................................... 19
10. ERROR CODES ..................................................................................................... 19
INSTALLATION MANUAL
PART NO. 9374342273
VRF system indoor unit (Duct type)
9374342273-01_IM.indb Sec1:1 9374342273-01_IM.indb Sec1:1 7/12/2012 10:18:57 AM 7/12/2012 10:18:57 AM