background image

 

 

 

IO-123090-GFW-020113 

- 5 - 

©2013 AirMark 

7)  Slide the 13/16 nut onto the distributor 

body. 

8) Tighten the nut to a torque of 

approximately 10-30 ft-lbs. Do 

NOT

 

over 

tighten the nut. This will hamper the piston 
movement during operation.  

9)  Slide the grommet back to position to 

prevent air leakage. 

 

 

TXV Coils: 

 

WARNING

  The sensing bulb and TXV body 

MUST

 be protected from overheating during 

brazing. The sensing bulb and TXV body must be 
covered using a quench cloth or wet cloth when 
brazing. Pointing the brazing flame away from the 
valve and sensing bulb provide partial protection 
only.  

 

 

CAUTION

  Ensure that the TXV selected is 

compatible with the refrigerant used in the outdoor 
system (R22 or R410A). TXV caps are painted 
green for R22 or pink for R410A. In absence of 
color, the caps will be marked with the compatible 
refrigerant. 

 

 

CAUTION

 The valves should be sized 

according to the capacity of the outdoor unit. 
Failure to install the right valve can lead to poor 
performance and possible compressor damage.  

 

TXV Bulb Mounting 

 

The orientation and location of the TXV bulb has a 
major influence on the system performance.  

 

CAUTION

   Ensure that the TXV bulb is in 

direct contact with the suction/vapor line. Gaps 
between the bulb and tube should be avoided. 
Failure to eliminate gaps will impair the proper 
functioning of the TXV valve.  

 

It is recommended that the TXV bulb be installed 
parallel to the ground (in a horizontal plane). The 
bulb position should be above and between 4 
o’clock and 8 o’clock. Fig. 4 shows the 
recommended position for the TXV bulb installation 
in the horizontal plane. 

 

The TXV sensing bulb 

SHOULD

 be mounted using 

the metal clamp provided. In order to obtain a good 
temperature reading and correct superheat control, 

the TXV sensing bulb must conform to ALL of the 
following criteria: 

 

1)  The sensing bulb 

MUST

 be in direct and 

continuous contact with the suction line 

2) The sensing bulb should be mounted 

horizontally on the suction line. 

3)  The sensing bulb must be mounted above 

and between the 4 and 8 o’clock position 
on the circumference of the suction line. 

4)  The sensing bulb 

MUST

 be insulated from 

outside air. 

 

TXV BULB POSITION
4 O'CLOCK OR
8 O'CLOCK 

METAL STRAP

SUCTION/VAPOR LINE

 

 

Fig.4. Recommended location of the TXV bulb in a 
horizontal orientation 
 

The mounting location and insulation guards the 
sensing bulb from false reading due to hot outside 
air or liquid refrigerant formed inside the 
suction/vapor line. 
 
As recommended earlier, the TXV sensing bulb 
should be mounted in a horizontal plane in relation 
to the suction/vapor line. However, in case such a 
mounting is not feasible and the sensing bulb has 
to be mounted vertically; then place the bulb as 
shown in Fig.5.  
 

Содержание GFW SERIES














Отзывы: