manualshive.com logo in svg

AirMan SDG100S-8B1, Инструкция по эксплуатации

Поделиться
Скачать
AirMan SDG100S-8B1 Скачать руководство пользователя страница 47

5. Periodic Inspection/Maintenance

 

 

5

-

6

 

H000049

 

A070316

5.5.2    Change Engine Oil Filter 

[At 50 hours for the first change and every 500 hours thereafter] 

<Procedure>

 

① 

When installing a new oil filter

“

1

”

, spread oil over 

the packing

“

2

”

, and then screw it in. When the 

packing touches the sealing surface, further tighten 
the filter by approximately two-thirds turn with a 
filter wrench. 

② 

After the oil filter

“

1

”

is assembled, check if there are 

any oil leaks during operation. (See 5.4) 

 
 

5.5.3  Check Insulation Resistance 

[Every 250 hours] 
 
 

 

When the generator has not been operated for a long time or moisture has entered inside the 
machine, be sure to measure the insulation resistance. If resistance is lower than 1M

Ω

, it could 

cause an electrical leakage or fire. Dry the generator with compressed air until the resistance exceeds 
1M

Ω

prior to operating.

 

 

Since the generator insulation may drop when moisture, oil vapor, and dust are stuck, always keep 
the machine clean.

 

 

<Procedure> <Megger tester required>

 

① 

Remove the load side cable from the output terminal 
board. 

② 

Remove the cable between the terminal “N” and terminal 
“Ground” which are connected on the back of the output 
terminal plate. 

③ 

Remove the AVR connector inside the generator control 
panel. 

④ 

Switch ON the three-phase breaker, measure each 
insulation resistance between the terminals L1. L2. L3 
terminal and bonnet. 

⑤ 

Insulation resistance when measured with a 500 V 
megger tester must be above 1 M

Ω

. 

⑥ 

After finishing the measurement of insulation resistance, 
re-connect the cable between the terminal "N" and 
terminal "Ground". 

 
 

 

After making sure that the insulation resistance of the 
generator is higher than 1 M

Ω

, be sure to re-connect the 

cable between the terminal "N" and terminal "Ground" just 
as it was originally connected.

 

If it is left disconnected, the grounding becomes imperfect 
so that it could cause electric shock

. 

 

A040180-1

Bonnet 

1 

2 

AVR Connector 

Discount-Equipment.com

Содержание SDG100S-8B1












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды