manualshive.com logo in svg

Aiqidi Smarine AiF5PS, Руководство пользователя

Поделиться
Скачать
Aiqidi Smarine AiF5PS Скачать руководство пользователя страница 108

 

Trouble Recovery 

Troubleshooting 

This section describes the likely causes and remedies for problems, such as those in the 

fuel, compression, and ignition systems, poor starting, and loss of power.Please note that 

all of the items in this section may not apply to your model. 

If your outboard motor requires repair, bring it to a dealer. 

Engine will not start.

 

Q. Is fuel tank empty? 

A. Fill tank with clean, fresh fuel. 

 

Q. Is fuel contaminated or stale? 

A. Fill tank with clean, fresh fuel. 

 

Q. Is fuel filter clogged? 

A. Clean or replace filter. 

 

Q. Is fuel pump malfunctioning? 

A. Have serviced by a dealer. 

 

Q. Is spark plug fouled or of incorrect type? 

A. Inspect spark plug. Clean or replace with recommended type. 

 

Q. Is spark plug cap fitted incorrectly? 

A. Check and re-fit cap. 

 

Q. Is spark plug wiring damaged or poorly connected? 

A. Check wires for wear or breaks. Tighten all loose connections .Replace worn or broken 

wires. 

 

Q. Are electrical parts malfunctioning? 

A. Have serviced by a dealer. 

 

Содержание Smarine AiF5PS





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды