Aim-TTI CPX400S Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 36

background image

33

IPADDR?

Returns the present IP address of the LAN interface, provided it is connected.
If it is not connected, the response will be the static IP if configured to always
use that static IP, otherwise it will be 0.0.0.0 if waiting for DHCP or Auto-IP.
The response is nnn.nnn.nnn.nnn<

RMT

>, where each nnn is 0 to 255.

NETMASK?

Returns the present netmask of the LAN interface, provided it is connected. The
response is nnn.nnn.nnn.nnn<

RMT

>, where each nnn is 0 to 255.

NETCONFIG?

Returns the first means by which an IP address will be sought.
The response is <

CRD

><

RMT

> where <

CRD

> is DHCP, AUTO or STATIC.

The following commands specify the parameters to be used by the LAN interface.

Note:

a power cycle is

required after these commands are sent before the new settings are used (or returned in response to the
queries listed above). The instrument does not attempt to check the validity of the IP address or netmask
in any way other than checking that each part fits in 8 bits. The rear panel LAN RESET switch will override
these commands and restore the defaults as described earlier.

NETCONFIG <

CPD

>

Specifies the means by which an IP address will be sought.

<

CPD

> must be one of DHCP, AUTO or STATIC.

IPADDR <quad>

Sets the potential static IP address of the LAN interface (as on the

webpage).
The parameter must be strictly a dotted quad for the IP address, with
each address part an <

NR

1> in the range 0 to 255, (e.g.

192.168.1.101).

NETMASK <quad>

Sets the netmask to accompany the static IP address of the LAN interface.

The parameter must be strictly a dotted quad for the netmask, with
each part an <

NR

1> in the range 0 to 255, (e.g. 255.255.255.0).

Miscellaneous Commands

*IDN?

Returns the instrument identification. The exact response is determined by
the instrument configuration and is of the form <NAME>,<model>, 0,
<version><

RMT

> where <NAME> is the manufacturer's name, <model>

defines the type of instrument and <version> is the revision level of the
software installed.

*TST?

The PSU has no self-test capability and the response is always 0 <

RMT

>.

*TRG

The PSU has no trigger capability. The command is ignored in this
instrument.

Error Messages

Each error message has a number; only this number is reported via the remote control interfaces.
Error message numbers are not displayed but are placed in the Execution Error Register where
they can be read via the remote interfaces, see Status Reporting section.

«
...
32
33
34
35
36
»

Содержание CPX400S





































Отзывы:

Нет отзывов

Похожие инструкции для CPX400S

Бренд: Fein Страницы: 43

Бренд: Fein Страницы: 166

Бренд: Panduit Страницы: 16

Nuron TE 500-22

Бренд: Hilti Страницы: 188

COMFORT CRIMP TBM21E

Бренд: Thomas & Betts Страницы: 2

Бренд: Parkside Страницы: 132

Бренд: MasterCraft Страницы: 30

Бренд: H&H Страницы: 20

Бренд: Parkside Страницы: 109

Бренд: Samlexpower Страницы: 4

Бренд: Inder Страницы: 2

Бренд: Skil Страницы: 60

Бренд: iBell Страницы: 16

Бренд: Power works Страницы: 136

Бренд: Cooler Master Страницы: 1

Бренд: Mussel Страницы: 25

Бренд: Prebena Страницы: 59

Бренд: Sealey Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды