manualshive.com logo in svg

ahlmann AS90, Руководство по обслуживанию, Страница: 12 / 18

Поделиться
Скачать
ahlmann AS90 Скачать руководство пользователя страница 12

S05E/S06E

8-12

8

Maintenance

1

3

4

2

8.2.13 Checking/adjusting the parking brake
play

DANGER

- All work on the brake system must only be carried

out by authorized personnel.

- Oil loss (leaks) in the brake system must be imme-

diately reported to authorized personnel.

(1) Check the brake's hydraulic oil level (4-10/4) and top

up if necessary.

(2) Pull the parking brake lever (8-27/arrow) and release it

again (lowest position).

CAUTION

The parking brake should become effective on the third

catch.

If the path the parking brake lever must travel before the

parking brake becomes effective is significantly longer, the

following work must be carried out:

NOTE

Figure 8-28 shows a top view of the front axle/chassis area.

1st possibility of an adjustment:

(3) Loosen the adjusting screw on the cable (8-28/3) from

the holder and turn it until the visible end of the thread is

reached.

(4) Tighten the adjusting screw (8-28/4) until it touches

the holder.

2nd possibility of an adjustment:

(5) Loosen the counter nut (8-28/2) at the steering head

(8-28/1).

(6) Unhook the steering head and turn it in clockwise

direction.

(7) Hook the steering head in again.

(8) Tighten the counter nut again.

CAUTION

- While adjusting the leverage, make sure to check

from time to time whether or not the parking brake

becomes effective on the 3rd catch.

- The parallel leverage must make contact with the

abutments (8-29/arrows) when the parking brake is

released.

(9) Perform a functional check.

Figure 8-27

Figure 8-29

Figure 8-28

Содержание AS90



















Отзывы:

Нет отзывов