manualshive.com logo in svg

ahlmann AS90, Руководство по обслуживанию, Страница: 11 / 18

Поделиться
Скачать
ahlmann AS90 Скачать руководство пользователя страница 11

S05E/S06E

8-11

Maintenance

8

2

1

8.2.10 Replacing the fuel filter

See the Engine Operating Instructions.

8.2.11 Exchanging the starter battery

NOTE

The starter battery is a maintenance-free part according to

DIN 72311, section 7. It is located to the right in the motor

compartment.

(1) Pull off the battery main switch (4-10/5).

(2) Open the motor hood.

(3) Remove the fastening screw (size 17) (8-24/1) of the

battery holder.

(4) Loosen and remove the connecting cables (8-24/2)

from the battery (size 13).

DANGER

Always remove the negative pole cable first and then the

positive cable. Installation is in the reverse order.

(5) Remove the battery and replace it.

(6) Apply grease to the connecting cables before faste-

ning them.

(7) Installation is in the reverse order.

DANGER

Make sure the fastenings are secure.

(8) Close the motor hood.

8.2.12 Maintaining/replacing the fresh air
filter

(1) Lift the bucket arm, insert the bucket arm support and

swivel the bucket arm all the way to the right or to the left.

(2) Loosen the four fastening screws (size 10) (8-25/

arrows) of the heater cover and remove the cover.

(3) Remove the filter elements (8-26/arrows) and clean

them with compressed air.

CAUTION

Do not use any petrol, hot fluids or compressed air for

cleaning.

(4) Check the filter elements for damage.

NOTE

The filter elements must be replaced when they are

damaged or every 

1500 operating hours

.

(5) Insert the filter elements and install the heater cover.

Figure 8-24

Figure 8-26

Figure 8-25

Содержание AS90



















Отзывы:

Нет отзывов