manualshive.com logo in svg

ahlmann AS90, Руководство по обслуживанию, Страница: 10 / 18

Поделиться
Скачать
ahlmann AS90 Скачать руководство пользователя страница 10

S05E/S06E

8-10

8

Maintenance

(3) Pull out the filter cartridge (8-22/arrow) by carefully

turning it back and forth.

(4) Clean the filter cartridge.

CAUTION

- For cleaning, use a compressed air gun to which a

pipe (angled at  90°) has been attached. The pipe

must be sufficiently long to reach the cartridge

bottom. Use dry compressed air of no more than

5 bar to blow out the cartridge by moving the pipe

back and forth in the interior of the cartridge.

Cleaning can be stopped when dust formation cea-

ses.

- Do not use petrol or hot liquid for cleaning.

(5) Use a hand-held lamp to check the filter cartridge for

damage to the cartridge paper or the rubber gasket. If the

cartridge or seals are damaged, replace the cartridge.

(6) Carefully insert the filter cartridge.

(7) Install the air filter lid on the filter housing in such a way

that the direction arrow in the marking 

“OBEN-TOP”

points towards half past one.

NOTE

The dust removal valve must be checked from time to time

and cleaned if necessary.

(8) When the indicator field becomes red (8-21/1), push

the reset button. The field becomes clear.

CAUTION

Check all connection pipes and hoses of the air filter

system for damage before starting the engine.

8.2.9

Changing the safety cartridge

CAUTION

- The safety cartridge must not be cleaned.

- The safety cartridge must be replaced after the filter

cartridge has been maintained/cleaned 5  times, at

the latest after two years.

- Make sure that no dirt or dust can enter the filter

housing during replacement of the safety cartridge.

(1) Remove the filter cartridge (section 8.2.8).

(2) Pierce the seal of the safety cartridge (8-23/arrow)

from the inside by using a screwdriver or similar tool and

pull up both strips.

(3) Hold the safety cartridge by both strips and pull it out

by carefully turning it back and forth. Replace the safety

cartridge and the filter cartridge by new ones.

(4) The remaining installation is performed as described

in section 8.2.8 (6)-(8).

Figure 8-22

Figure 8-23

Содержание AS90



















Отзывы:

Нет отзывов