Agria 3600 075 Скачать руководство пользователя страница 26

Страница: 26 / 76

3 Devices and Operating Elements

Two-wheel tractor

agria 3600

Shift gears only when the machine is at standstill (disengaged)!

Gear shifting

The gears 1 - 2 and R1 - R2 are shifted with the
gear shifting rod (B/7)!

Idle position "0" between the individual gears.

The 3rd gear ("overdrive") is selected with

over-

drive shifting

(see below).

The selected gear shows at the sticker on the
gearbox.

Actuate the clutch before you switch gears.

Overdrive shifting

with version 3600 (3+2)

For transport rides, you can use the 3rd gear
(overdrive).

•

This requires the overdrive shifting rod (B/8)
to be installed. See page 10

•

Switch the gear shifting rod (B/7) to position
"0" between 1st and R1 gear.

•

Switch the overdrive shifting rod (B/8) to
position "(FAST)" (pull the shifting rod to the
rear).

•

Switch the gear shifting rod to position "3".

•

Switch back in reverse sequence.

•

To switch to a reverse gear, first set the
shifting rod to "0", and switch off the "Over-
drive".

For safety reasons, "overdrive shifting" is only
possible during normal forward driving (rear
implement attachment). With front implement
attachments, the overdrive shifting rod is re-
moved and switching is blocked.

Содержание 3600 075













































































Результаты поиска

Содержание 3600 075

Отзывы:

Бренды по названию

Популярные бренды

Agria 3600 075, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание 3600 075

Отзывы:

Бренды по названию

Популярные бренды