background image

15

Victrix  

USER MANUAL

If the position of the FSM’s clamping nut is uncomfortable, change it as follows:
1. Decide on desirable position of the nut and estimate the angle through which the FSM should be 

turned CW (see Figure 2-8).

2. Remove the FSM from the Victrix.
3. Using a screwdriver, remove the M2×2.5 screws (F, see Figure 2-7) and then unscrew the ring (E).

FIGURE 2-8. ESTIMATION OF THE FSM TURNING ANGLE

NUT

DESIRABLE POSITION 

OF THE NUT

CAUTION:

To loosen the ring (E, Figure 2-7), use the two auxiliary non-threaded holes (D). DO NOT 

USE the threaded ones.

4. Using a lathe or other precision cutting tool, cut the inside face of the ring (E, Figure 2-7). The 

value of cuts (in millimeters) should be equal to the value of the turning angle (in angular 

degrees) divided by 360°.

5. Screw the ring (E) into the FSM’s body with its cut end directed inwards. Tighten the screw.
6. After applying a small amount of thread lock to the threads, affix the ring (E) using the two 

M2×2.5 screws (F).

2.1.5  INSTALLING THE LIGHT SUPPRESSOR FOR A DAY SCOPE

The Light Suppressor for a Day Scope (A, Figure 2-9) slides over the eyepiece of your daytime 

scope (B). The suppressor can be used with scopes that have 40-43 mm eyepiece diameters and 

100-120 mm eye relief.
The suppressor can be adjusted for the eye relief of your scope by cutting the rubber at the desired 

distance (C).

FIGURE 2-9.  LIGHT SUPPRESSOR FOR A DAY SCOPE

A

B

C

Содержание VICTRIX





































Отзывы: