background image

RATTLER TC35-640/TC50-640  

USER MANUAL

3

FCC INFORMATION

Please take attention that changes or modification not expressly approved by the 

party responsible for compliance could void the user’s authority to operate the 

equipment.

This equipment complies with FCC/IC RSS-102 radiation exposure 

limits set forth for an uncontrolled environment. 

FCC compliance: This product has been tested and found to comply with the 

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These 

limits are designed to provide reasonable protection against harmful interference 

in a residential installation. This product generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If this product 

does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following measures: 
— Reorient or relocate the receiving antenna. 
— Increase the separation between the equipment and receiver. 
— Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 
— Consult the dealer or an experienced radio/TV technician for help.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the 

following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that 

may cause undesired operation.

EU CONFORMITY STATEMENT

This product and - if applicable - the supplied accessories too 

are marked with “CE” and comply therefore with the applicable 

harmonized European standards listed under the EMC Directive 

2014/30/EU, the RoHS Directive 2011/65/EU 

2012/19/EU (WEEE directive): Products marked with this symbol 

cannot be disposed of as unsorted municipal waste in the 

European Union. For proper recycling, return this product to your 

local supplier upon the purchase of equivalent new equipment, or 

dispose of it at designated collection points. For more information 

see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that 

cannot be disposed of as unsorted municipal waste in the European 

Union. See the product documentation for specific battery 

information. The battery is marked with this symbol, which may 

include lettering to indicate cadmium (Cd), lead (Pb), or mercury 

(Hg). For proper recycling, return the battery to your supplier 

or to a designated collection point. For more information see: 

www.recyclethis.info

INDUSTRY CANADA ICES-003 COMPLIANCE

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

Содержание RATTLER TC35-640

































Отзывы: