background image

RATTLER TC35-640/TC50-640  

USER MANUAL

5

SAFETY SUMMARY

•  Read and follow all instructions
•  Read all warnings
•  Only use the attachments/accessories specified by the manufacturer
•  All service must be provided by the manufacturer

WARNING:

This product contains natural rubber latex, which may cause potentially fatal 

allergic reactions! If you are allergic to latex, it is important that you strictly 

avoid exposure to products that contain it. 

 WARNING:

Always make sure your firearm is unloaded before you place the scope on the 

firearm. Reconfirm that the chamber is empty if you stop the procedure then 

resume later. Safe handling rules should be followed at all times. 

WARNING:

If a scope is mounted too far to the rear, the eyepiece can injure the shooter’s 

brow. Shooting at an uphill angle also increases this hazard because it 

shortens the distance between the brow and the rear of the scope. For this 

reason, AGM scopes are engineered to provide generous eye relief. Therefore, 

when mounting your scope, we recommend positioning it as far forward in the 

mounts as possible to take full advantage of this generous eye relief. With hard-

recoiling rifles, serious injury or even death can result from eyepiece impact 

with the shooter during the recoil process when discharging the firearm. 

Be certain that your installation provides sufficient eye relief for the recoil 

generated by your rifle before shooting the firearm. 
NOTE: Give special attention to this warning when shooting uphill and/or from 

a prone position. These shooting conditions can dramatically reduce eye relief. 

PLEASE maintain maximum eye relief when shooting heavy recoiling and/or 

magnum firearms. THE USER ASSUMES ALL RESPONSIBILITY AND LIABILITY 

FOR HAVING THE AGM SCOPE PROPERLY MOUNTED TO A FIREARM AND 

USING THE AGM SCOPE PROPERLY. ALWAYS CHECK THE CONDITION OF 

YOUR MOUNTING SYSTEM PRIOR TO USING YOUR FIREARM.

WARNING:

The proper usage of the device is important for safe operation! 

Therefore carefully read this manual!

WARNING: 

If the device was left in storage for a longer period of time, before use, check 

its functionality.

WARNING: 

Disassembling of the device is prohibited, except in authorized repair centers.

WARNING: 

Please remove the batteries from the battery compartment before connecting 

the device to your PC, or it may cause computer damage.

Содержание RATTLER TC35-640

































Отзывы: