manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Установочная инструкция, Страница: 41 / 46

Поделиться
Скачать
Agilent Technologies E8363BU/CU-068 Скачать руководство пользователя страница 41

Installation Note E8364-90023                                                                                                                         

 

41

Step 11. Reinstall the Front Panel Assembly and Front Panel Jumpers

CAUTION

Before installing the front panel assembly onto the analyzer, lift and support the 
front of the analyzer chassis. 

1. Reconnect the ribbon cable (item 

①

) to the A3 front panel interface board.

2. Slide the front panel over the test port connectors being careful to align the power switch 

and floppy disk drive to their corresponding front panel cutouts. Ensure that the ribbon 
cable (item 

①

) is located below the fan to prevent it from being damaged by the fan blades.

3. Using a T-10 TORX driver, install the eight screws (item 

②

) in the sides of the frame.

4. Install the six semirigid jumpers, W60, (item 

③

) on the front panel, and, using a 5/16-inch 

torque wrench, tighten the connector nuts to 10-in lbs.

Figure 28

Front Panel Assembly Reinstallation

NOTE

The figure above shows the E8364B front panel and floppy disk drive. The 
E8363C and E8364C front panel have a slightly different appearance and 
does not include a floppy disk drive. 

Содержание E8363BU/CU-068















































Отзывы:

Нет отзывов