Agilent Technologies E8363BU/CU-068 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 46

Agilent Technologies E8363BU/CU-068 Скачать руководство пользователя страница 11

Installation Note E8364-90023

11

Test Equipment Required for Post-Upgrade Adjustments

Step 1. Obtain a Keyword and Verify the Information

Follow the instructions on the Option Entitlement Certificate supplied to obtain a license key
for installation of this upgrade. Refer to

“License Key Redemption” on page 4

.

Verify that the model number, serial number, and option number information on the license
key match those of the instrument on which this upgrade will be installed.

If the model number, serial number, or option number do not match those on your license key,
you will not be able to install the option. If this is the case, contact Agilent for assistance
before beginning the installation of this upgrade. Refer to

“Contacting Agilent” on page 3

.

Once the license key has been received and the information verified, you can proceed with the
installation at step 2.

Description

Agilent Part Number

Power meter

E4418B/E4419B

Power sensor, Type-N (100 kHz–4.2 GHz)

8482A

Power sensor, 2.4 mm (4.2 GHz–50 GHz)

8487A

Power sensor, V-Band (50 GHz–67 GHz)

a

a. This sensor and adapter must be calibrated together by the Agilent factory. The data supplied

are only valid as long as the sensor and adapter remain connected.

V8486A

Adapter, WR-15 to 1.85 mm (m)

V281B

Adapter, 1.85 mm (f) to 1.85 mm (f)

b

b. The 1.85 mm connector has the same ruggedness and is compatible with the 2.4 mm connec-

tor. 1.85 mm and 2.4 mm connectors and adapters may be used interchangeably.

85058-60114

Adapter, 3.5 mm (m) to 2.4 mm (f)

11901D

Adapter, 2.4 mm (f) to 2.4 mm (f)

11900B

Adapter, Type-N (f) to 2.4 mm (f)

11903B

Adapter, SMA (m) to SMA (f), right angle

1250-1249

Test cable, 2.4 mm (f) to 2.4 mm (f)

Test cable, 1.85 mm (f) to 1.85 mm (f)

85133C

N4697E

5/16-inch, open-end torque wrench (set to 10 in-lbs)

8710-1765

1/4-inch, open-end wrench, thin profile

8710-0510

«
...
9
10
11
12
13
...
»

Содержание E8363BU/CU-068















































Отзывы:

Нет отзывов