Agilent Technologies E8363BU/CU-068 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 46

Agilent Technologies E8363BU/CU-068 Скачать руководство пользователя страница 3

Installation Note E8364-90023

3

Description of the Upgrade

This upgrade kit is used to extend the frequency range of the E8363 B/C, or E8364B/C, Option
014 PNA microwave network analyzer from 40 GHz to 67 GHz, or 50 GHz to 67 GHz.

This upgrade applies to a PNA with only Option 014 or Option 014 and 080 in combination.
No other optional hardware combinations can be upgraded with this upgrade kit. If options
016, 081, UNL, or H11 are already installed, special upgrade instructions are required. Stop
here and contact Agilent for these instructions.

Getting Assistance from Agilent

Installing this upgrade kit requires special skills and experience. If you think you may not be
qualified to do the work, or need advice, contact Agilent.

Contacting Agilent

Assistance with test and measurements needs and information on finding a local Agilent
office are available on the Web at:

http://www.agilent.com/find/assist

If you do not have access to the Internet, please contact your Agilent field engineer.

NOTE

In any correspondence or telephone conversation, refer to the Agilent product by
its model number and full serial number. With this information, the Agilent
representative can determine whether your product is still within its warranty
period.

«
1
2
3
4
5
...
»

Содержание E8363BU/CU-068















































Отзывы:

Нет отзывов