Agilent Technologies E8362C Скачать руководство пользователя страница 266

Страница: 266 / 382

7-10

Service Guide E8364-90038

Repair and Replacement Procedures

PNA Series Microwave Network Analyzers

Removing and Replacing the Front Panel Assembly

E8362C, E8363C, E8364C

Removing and Replacing the Front Panel Assembly

Tools Required

•

T-10 TORX driver (set to 9 in-lb)

•

T-20 TORX driver (set to 21 in-lb)

•

5/16 inch open-end torque wrench (set to 10 in-lb)

•

ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-3

for this procedure.

1. Disconnect the power cord.

2. Remove the outer cover. Refer to

“Removing the Covers” on page 7-6

3. With a 5/16 inch torque wrench, remove all the semirigid jumpers (item

①

) from the front panel (Option

014 only).

4. With a T-10 TORX driver, remove the eight screws (item

➁

) from the sides of the frame.

CAUTION

Before removing the front panel from the analyzer, lift and support the front of the analyzer
frame.

5. Slide the front panel over the test port connectors.

6. Disconnect the front panel interface ribbon cable (item

③

The front panel is now free from the analyzer.

Replacement Procedure

CAUTION

When replacing the front panel, be sure to align the power switch to its corresponding front
panel cutout.

IMPORTANT

When reconnecting semirigid cables, torque the cable connectors to 10 in-lb.

1. Reverse the order of the removal procedure.

2. Perform the post-repair adjustments, verifications, and performance tests that pertain to this removal

procedure. Refer to

Table 7-2 on page 7-82

Содержание E8362C































































































































































































































































































































































































Результаты поиска

Содержание E8362C

Отзывы:

Похожие инструкции для E8362C

Бренды по названию

Популярные бренды

Agilent Technologies E8362C, Руководство по обслуживанию

Результаты поиска

Содержание E8362C

Отзывы:

Похожие инструкции для E8362C

Бренды по названию

Популярные бренды