Agilent Technologies E8362A PNA Series Скачать руководство пользователя | Manualshive

Страница: 8 / 32

background image

8

Installation Note E8362-90016

ESD Equipment and Supplies Required for the Installation

Equipment Required for Post-Upgrade Adjustments

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Refer to the License Key Certificate supplied with the kit:

• Verify that the analyzer’s model and serial numbers match those on the certificate.

• Verify that the option number on the certificate matches the option described by this

installation note.

If the model, serial, or option number do not match the expected results, you will not be able
to install the option. If this is the case, contact Agilent for assistance. Refer to

“Contacting

Agilent” on page 3

.

Description

Agilent Part Number

ESD grounding wrist strap

9300-1367

5-ft grounding cord for wrist strap

9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire

9300-0797

ESD heel strap (for use with conductive floors)

9300-1308

Equipment Type

Model or
Part Number

Alternate Model or
Part Number

Power meter

E4418B/E4419B

E4418A/E4419A

Power sensor, 2.4 mm

8487A

None

Adapter, 2.4 mm (f) to 2.4 mm (f)

11900B

85056-60007

RF cable, 2.4 mm (f) to 2.4 mm (f)

85133C

85133E

«
...
6
7
8
9
10
...
»

Содержание E8362A PNA Series

































Отзывы:

Нет отзывов

Похожие инструкции для E8362A PNA Series

Бренд: Farfisa Страницы: 14

Бренд: Valmet Страницы: 63

Бренд: Hammond Страницы: 130

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 99

Бренд: NARDA Страницы: 64

Бренд: Keithley Страницы: 343

Бренд: Keithley Страницы: 334

Бренд: La Crosse Technology Страницы: 2

Electone Stagea ELS-01C

Бренд: Yamaha Страницы: 248

WM14-96 - PROGRAMMING

Бренд: CARLO GAVAZZI Страницы: 6

Бренд: Kingfisher Страницы: 52

WARREN ELLIS SIGNATURE TENOR BARITONE

Бренд: Eastwood Guitars Страницы: 4

Бренд: Fluke Страницы: 32

Бренд: Omega Страницы: 4

Бренд: Racelogic Страницы: 15

Бренд: Readiness Systems Страницы: 16

Бренд: Fluke Страницы: 134

Бренд: Huazheng Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды