Agilent Technologies AIC 5000 Скачать руководство пользователя | Manualshive

Страница: 22 / 64

background image

16

AIC 5000 Installation and Configuration

4.

Restart the AIC.

5.

Start the data system from

Start > All Programs >

Chromatography > EZChrom Elite

. When you are prompted

that you‟ve been assigned rights and you must restart, restart
the AIC.

Once the AIC 5000 configuration is completed, go on to the next
sections to connect hardware and instruments.

Install an A/D Converter

If your instrument provides an analog detector signal, you must use
an analog to digital (A/D) converter. If you are using a digital
instrument, you do not need an A/D converter.

Install the SS420x

If your instrument provides an analog detector signal, you may use
the SS420x analog to digital converter box. If you are using a digital
instrument, you do not need an SS420x.

Connect the SS420x interface to the AIC using the serial
communications cable provided. Connect one end of the cable to
the serial port on the back of the SS420x. Connect the other end of
the cable to any serial port on the AIC (see Figure 3 below.) Make
sure to tighten each connector.

Connect the power cord into the receptacle on the rear of the
SS420x and then plug the SS420x power supply into a standard
electrical outlet.

The SS420x red power LED should light. The four (4) green
channel indicator LEDs will sequentially light up during the power-
up test. When the test is complete, the green LEDs will go off and
the interface is ready to use. If this sequence does not successfully
complete, the SS420x must be powered off and then on again.

For more information, see the

Agilent SS420x Interface User’s

Guide

.

«
...
20
21
22
23
24
...
»

Содержание AIC 5000

































































Отзывы:

Нет отзывов

Похожие инструкции для AIC 5000

Бренд: GE Страницы: 8

Бренд: Garmin Страницы: 4

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

FUTERA XLF Series

Бренд: RBI Страницы: 128

Бренд: RBH Access Technologies Страницы: 36

Бренд: S&C Страницы: 11

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 19

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Data Signs Страницы: 23

Бренд: HW Group Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды