Agilent Technologies 6631B Скачать руководство пользователя страница 75

Страница: 75 / 75

Manual Updates

The following updates have been made to this manual since the November 1997 printing indicated on the
Printing History page.

7/8/99

Additional information about CV mode operation has been added to page 20.

A note has been added to Table A-1 for the Ripple and Noise specifications and a correction has been
made for Model Agilent 6631B.

Steps 22 and 23 on page 61 under Low Range Current Measurement Calibration have been switched.

1/7/00

All references to HP have been changed to Agilent.

All references to HP-IB have been changed to GPIB.

A note about magnetic fields has been added to page 22.

On page 49 the model reference for note 2 has been corrected.

2/21/01

A note has been added to Table A-1 for the Programming Accuracy specification.

Information about Option 760 has been added to Table A-1, note 5

The values for Average Programming Resolution, Current in table A-2 have been adjusted.

5/01/02

Step 19 on page 56 under Negative Current Programming Calibration has been corrected.

10/2/03

The Ripple and Noise specification for Model 6634B has changed in table A-1.

3/9/04

The ac input ratings and fuse information has been updated as per IEC 61010-1 requirements throughout
the manual.

The Declaration of Conformity has been updated on page 5.

Содержание 6631B












































































Результаты поиска

Содержание 6631B

Отзывы:

Похожие инструкции для 6631B

Бренды по названию

Популярные бренды

Agilent Technologies 6631B, Руководство пользователя

Результаты поиска

Содержание 6631B

Отзывы:

Похожие инструкции для 6631B

Бренды по названию

Популярные бренды