Agilent Technologies 6631B Скачать руководство пользователя страница 69

Страница: 69 / 75

Line Voltage Conversion

WARNING:

Shock Hazard Operating personnel must not remove instrument covers.
Component replacement and internal adjustments must be made only by qualified
service personnel.

Open the Unit

♦

Turn off ac power and disconnect the power cord from the unit.

♦

Remove the four screws that secure the cover (use a #2 Pozi drive).

♦

Slightly spread the bottom of the cover and pull it back to remove it from the unit.

Configure the Power Transformer

♦

Locate the ac input wiring harness on the left side of the transformer.

♦

Use a needlenose pliers and connect the ac input wiring harness according to the information in the
following figure:

grey

white/red/grey

jumper

grey

white/red/grey

jumper

grey

white/red/grey

jumper

grey

white/red/grey

jumper

spare

Figure D-1, Power Transformer AC Input Connections

Содержание 6631B












































































Результаты поиска

Содержание 6631B

Отзывы:

Похожие инструкции для 6631B

Бренды по названию

Популярные бренды

Agilent Technologies 6631B, Руководство пользователя

Результаты поиска

Содержание 6631B

Отзывы:

Похожие инструкции для 6631B

Бренды по названию

Популярные бренды